Question is ⇒ Which of the following statement is correct?, Options are ⇒ (A) A FET is a current controlled device, (B) A BJT is always reverse biased, (C) The semi-conductor material of the gate in an N-channel JFET is <i>p</i>-type, (D) JFET has higher input impedance than MOSFET, (E) , Leave your comments or Download question paper.

Question is ⇒ Which of the following statement is correct?, Options are ⇒ (A) A FET is a current controlled device, (B) A BJT is always reverse biased, (C) The semi-conductor material of the gate in an N-channel JFET is <i>p</i>-type, (D) JFET has higher input impedance than MOSFET, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Which of the following statement is correct?
A.	A FET is a current controlled device [Wrong Answer]
B.	A BJT is always reverse biased [Wrong Answer]
C.	The semi-conductor material of the gate in an N-channel JFET is p-type [Correct Answer]
D.	JFET has higher input impedance than MOSFET [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Secondary emission results
when temperature of metals is raised to a level above the crystallization temperature
when metals are subjected to strong magnetic fields
when light rays fall on the metal surface
when a high velocity beam of electrons strikes as metal surface

⇒ Two network said to be dual to each other
if mesh equation of one is same to other of node equation
if mesh equation of both is same
if node equation of both is same
neither mesh equation nor node equation is same

⇒

Assertion (A): Ferrites are very useful at very high frequencies.

Reason (R): Ferrites have high permeability and high resistivity.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true

⇒ Household taperecorders generally use
crystal microphone
moving coil microphone
condenser microphone
cardioid microphone

⇒ A sinusoidal ac voltage of amplitude 100 V is applied to a rectifying device which offers 10 Ω resistance in forward direction and infinite resistance in reverse direction. The reading on hot wire ammeter will be
0.416666666666667
0.208333333333333
3.185 A
1.414 A

⇒ The abbreviation DTL stands for
Digital Timing Logic
Diode Transistor Logic
Dynamic Transient Logic
Delayed Tracking Logic

⇒ In figure what is value of I_C if β_dc = 100. Neglect V_{BE5 mA
5 μA
10 mA
10 μA}

⇒ Which one of the following is used as the interface chip for data transmission between 8086 and a 16-bit ADC?
8259
8255
8253
8251

⇒ The effect of negative feedback on distortion and bandwidth because
both are decreased
both are increased
distortion is reduced and bandwidth is increased
distortion is increased and bandwidth is decreased

⇒ A 3 x 8 decoder with two enable inputs is to be used to address 8 blocks of memory. What will be the size of each memory block when addressed from a sixteen bit bus with two MSBs used to enable the decoder?
2 K
4 K
16 K
64 K

⇒

Assertion (A): The amount of photoelectric emission depends on the intensity of incident light.

Reason (R): Photo electric emission can occur only if frequency of incident light is less than threshold frequency.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ For underdamped second order systems the rise time is the time required for the response to rise from
0% to 100% of its final value
10% to 90% of its final value
5% to 95% of its final value
either (a) or (b)

⇒ The depletion layer in a reverse biased p-n junction is due to the presence of
electrons
holes
both electrons and holes
immobile ions

⇒ In a material, the Fermi level is located between the centre of the forbidden band and the conduction band. Then what is that material?
A p-type semiconductor
An n-type semiconductor
An intrinsic semiconductor
An insulator

⇒ The dominant mode in a rectangular wave-guide is
TE₀₁
TM₀₁
TE₁₀
TM₁₁

⇒ A remote control of TV uses a 10 bit word. The maximum number of total commands it can transmit is
64
256
512
1024

⇒ A 0-200 V voltmeter has an accuracy of 0.75% of full scale reading. If voltage measured is 100 V, the error is
0.03
0.02
0.015
0.0075

⇒ In figure, the function of resistor
to reduce ripples in the output
to improve voltage regulation
to limit the surge current
either (a) or (c)

⇒ A triangular Pulse of 10 V peak is applied to a capacitor of 0.4 F. The change of the capacitor and its wavefor
8 rectangular
8 triangular
4 triangular
4 rectangular

⇒ Which of the following devices is used in the microprocessors?
JFET
BJT
MOSFET
CMOS

⇒ A short circuited stub is shunt connected to a transmission line as shown in the figure is, if z₀ = 500 ohms, the admittance y seen at the function of the stub and the transmission line
(0.01 - j 0.02) mho
(0.02 - j 0.01) mho
(0.04 - j 0.02) mho
(0.02 + j 0) mho

⇒ When an alternating current passes through an ohmic resistance the electrical power converted into heat is
apparent power
true power
reactive power
none of the above

⇒ The accumulator drives the ALU.
TRUE
FALSE

⇒ A cycloconverter cannot give a frequency higher than input frequency.
TRUE
FALSE

⇒ Read the following statements: Dual slope ADC provides

higher speed as compared to other ADC
very good accuracy
good rejection of power supply
better resolutions compared to other ADC for the same number of bits

Which of the above are correct?
1 and 2
2 and 3
1, 2, 3
1, 2, 3, 4

⇒ The inductance of a single layer solenoid of 10 turns is 5 μH. Which one of the following is the correct value of inductance when the number of turns is 20 and the length is doubled.
10 μH
20 μH
40 μH
5 μH

⇒ The function shown in the fig
impulse function
signum function
unit step function
none of the above

⇒ A multimeter can be used as ohmmeter.
TRUE
FALSE

⇒ In 8085 microprocessor, which of the following is not vectored interrupt?
RST 5.5
RST 6.5
RST 7.5
INTR

⇒ A rectifier circuit has load resistance R. It uses a capacitance filter having capacitance C. For low ripple in the output
RC should be 1
RC should be low
RC should be high
RC should be neither low nor high