Question is ⇒ Which of the following statement about the amplitude limiter is not valid?, Options are ⇒ (A) Leak type bias must be used, (B) Output must be tuned, (C) The circuit is always biased in class <i>C</i>, by virtue of the leak type bias, (D) When the input increases past the threshold of limiting, the gain decreases to keep the output constant, (E) , Leave your comments or Download question paper.

Question is ⇒ Which of the following statement about the amplitude limiter is not valid?, Options are ⇒ (A) Leak type bias must be used, (B) Output must be tuned, (C) The circuit is always biased in class <i>C</i>, by virtue of the leak type bias, (D) When the input increases past the threshold of limiting, the gain decreases to keep the output constant, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Which of the following statement about the amplitude limiter is not valid?
A.	Leak type bias must be used [Wrong Answer]
B.	Output must be tuned [Wrong Answer]
C.	The circuit is always biased in class C, by virtue of the leak type bias [Correct Answer]
D.	When the input increases past the threshold of limiting, the gain decreases to keep the output constant [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Assuming accumulator contain A 64 and the carry is set (1). What will register A and carry (CY) contain after ORA A?
A 6 H, 1
A 6 H, 0
00 H, 0
00 H, 1

⇒

Assertion (A): The circuit of figure thyristor will conduct for 180° during positive half cycle if it is continuously fir
Both A and R are correct and R is correct explanation of A
Both A and R correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ The characteristics of a non-linear resistance is i = kv⁴. If i becomes 100 times, v becomes
about 100 times
about 10 times
about 3 times
about twice

⇒ For good quality signal transmission all frequency components should have the same transmission delay, t_d and same phase shift-Φ_s. What can be said about the statement?
Correct
True from t_d but not for Φs
Not true for t_d but true for Φ_s
Both t_d and Φ_s are not involved in quality

⇒

Assertion (A): Absolute instruments are used in standard laboratories.

Reason (R): Absolute instruments do not require calibration.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒

Match the following:

	List I		List II
A.	C	1.	7 eV
B.	Si	2.	1.15 eV
C.	Ge	3.	0.75 eV
D.	Sn	4.	0.1 eV
E.	Pb	5.	0 eV

A-2, B-3, C-4, D-5, E-1
A-1, B-2, C-3, D-4, E-5
A-3, B-1, C-2, D-5, E-4
A-4, B-5, C-1, D-2, E-3

⇒ The minority carrier life time and diffusion constant in a semiconducting material are 100 μs and 100 cm²/s respectively. The diffusion length of carriers is
0.1 cm
0.01 cm
0.0141 cm
1 cm

⇒ An n channel JFET has I_DS whose value is
maximum for V_GS = 0 and minimum for V_GS negative and large
minimum for V_GS = 0 and maximum for V_GS negative and large
maximum for V_GS = 0 and minimum for V_GS positive and large
minimum for V_GS = 0 and maximum for V_GS positive and large

⇒ What is the RF amplifier plate voltage when the audio-modulating voltage is +600
-600 V
Zero
600 V
1200 V

⇒ The oscillator shown in figure
Colpitt's oscillator
Hartley oscillator
Tuned emitter oscillator
Clapp oscillator

⇒ Which of these has degenerate p and n materials?
Zener diode
PIN diode
Tunnel diode
Photo diode

⇒ In Fortran 77 negation is a unary operation.
TRUE
FALSE

⇒ In which configuration does output ac voltage appear between emitter and ground?
CE
CB
CC
Both CE and CB

⇒ Spot the odd one out
aluminium
silver
porcelain
copper

⇒ In ac circuits maximum power is delivered to a load if load impedance is conjugate of source impedance.
TRUE
FALSE

⇒ A circuit using an op-amp is shown in the given figure. It
voltage series feedback
voltage shunt feedback
current shunt feedback
current series feedback

⇒ Fourier analysis indicate that a square wave can be represented as
a fundamental sine wave and odd harmonics
a fundamental sine wave and even harmonics
a fundamental sine wave and harmonics
fundamental and subharmonic sine waves

⇒ Semi conducting materials are all
elements
compounds
elements or compounds
elements or mixtures

⇒

Assertion (A): The 'do while' statement is used less frequently than the 'while' statement.

Reason (R): For most applications it is more natural to test for continuation of loop at the beginning than at the end of loop.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ A P-channel MOSFET operating in the enhancement mode is characterized by V_t = - 4 V and I_DQ = - 10 mA, when V_GSQ = - 5.5 V, what will be V_GSQ if I_DQ = -15 mA and I_{D, on} = - 16 mA
- 2 V
3 V
0.13 V
1.3 V

⇒ In a ferromagnetic material, the internal field seen by a dipole is
equal to applied field
equal to applied field minus a contribution from neighbouring dipoles
equal to applied field plus a contribution from neighbouring dipoles
equal to or less than applied field

⇒ The attenuation characteristics of a loaded line is similar to that of
low pass filter
high pass filter
band pass filter
band stop filter

⇒ The internal impedance of a source is 3 + j 7 Ω. For maximum power transfer, load impedance should be
3 + j 7 Ω
3 - j 7 Ω
7 + j 3 Ω
7 - j 3 Ω

⇒ Magnetic flux density has the dimensions
MI^-1T^-2
M^-1I^-2T^-2
ML^-3T^-2
MI^-1T^-3

⇒ In figure v₁ = 8 V and v₂ = 4 V. Which diode will cond
D₂ only
D₁ only
Both D₁ and D₂
Neither D₁ nor D₂

⇒ The organisatioion of Intel memory chip 127256 is
32 K x 8
16 K x 8
32 K x 4
16 K x 4

⇒ For a distortionless line, the parameters are related as
R/G = L/C
R/L = 1
R/G = C/L
RG = LC

⇒ Audio tapes have two tracks each 2.5 mm wide.
TRUE
FALSE

⇒ ECL has high switching speed because the transistors are
switching between cutoff and saturation regions
switching between cutoff and active regions
switching between active and saturation regions
none of the above

⇒ The number of possible colours with a 4 line digital input monitor are
4
16
64
2