Question is ⇒ Which of the following parameters is not specified for digital ICs?, Options are ⇒ (A) Gate dissipation, (B) Propagation delay, (C) Noise margin, (D) Bandwidth, (E) , Leave your comments or Download question paper.

Question is ⇒ Which of the following parameters is not specified for digital ICs?, Options are ⇒ (A) Gate dissipation, (B) Propagation delay, (C) Noise margin, (D) Bandwidth, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Which of the following parameters is not specified for digital ICs?
A.	Gate dissipation [Wrong Answer]
B.	Propagation delay [Wrong Answer]
C.	Noise margin [Wrong Answer]
D.	Bandwidth [Correct Answer]
View Answer 2 -3 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ India's Polar Satellite Launch vehicle (PSLV) to be ready in 1991 is designed to launch 1000 kg spacecraft into __________ orbit.
geostationary
equatorial
polar
sun-synchronous polar

⇒ A metal loses electrons at room temperature.
TRUE
FALSE

⇒ In a cellular communication system, path loss between transmitter and receiver is due to
scattering from building, trees, vehicles and other structure
reason at (a) above and due to reflections from ground only
reason at (a) and (b) above along with reflections from ionosphere only
reasons at (a), (b) and (c) above along with loss due to surface wave phenomenon

⇒ In 8085 microprocessor, in order to enable INTR interrupt, which of the following instruction are needed?
EI only
SIM only
El and SIM both
None

⇒ In a radio receiver, if the intermediate frequency is too high
Selectivity will be poor
Tracking difficulties will be least
Adjacent channel rejection will improve
All of the above will occur

⇒ Consider following statements :

Maximum energy of electrons liberated photoelectrically is independent of light intensity
Maximum energy of electrons liberated photoelectrically varies nonlinearly with frequency of incident light.

statement (1) is true and (2) is false
statement (1) and (2) both are true
statement (1) is false and (2) is true
statement (1) and (2) both are false

⇒ The multiplication time for 10-bit numbers with 1 MHz clock will be
32 μ sec
20 μ sec
21 μ sec
22 μ sec

⇒ Which of the following binary product is incorrect?
1100 x 1010 = 1111000
1.01 x 10.1 = 11.001
1100110 x 1000 = 1100110000
None of the above

⇒ Choose the correct statement/statements :
In case of an antenna, the antenna resistance and loss resistance are not two different quantities.
The loss resistance includes loss by eddy currents, improper earth connections, insulation leakages, etc., but not I²R losses.
Radiation resistance varies directly as square-root of frequency
None

⇒ Magnetic effect of current is used in
ammeters
voltmeters
wattmeters
ammeters, voltmeters, wattmeters and energy meters

⇒ In 8085 the address space size is
64 kbits
64 k bytes
32 kbits
16 k bytes

⇒ Which of the following devices uses a slow wave structure?
Klystron two cavity amplifier
Klystron multicavity amplifier
Reflex klystron oscillator
TWT

⇒ Find the power absorbed or delivered by each sou
a = -32 b = - 12 c = -80 d = -60
a = -32 b = - 12 c = 80 d = 60
a = 32 b = 12 c = -80 d = 60
a = -32 b = 12 c = 80 d = -60

⇒ In an integrated circuit the SiO₂layers provide
electrical connection to external Ckt.
physical strength
isolation
conducting path.

⇒ At millimeter wavelength the favoured mode in circular wave guide is
TE₀₁
TE₁₁
TE₂₀
TE₂₁

⇒ The content of which of the following determines the state of the CPU at the end of the execute cycle (when the interrupt is recognized)?

Program counter
Processor register
Certain status conditions

Select the correct answer using the codes given below :
1 and 2
2 and 3
1 and 3
1, 2 and 3

⇒ A coil has resistance R and inductance L. At ω = ∞ the phase angle between voltage and current is
0°
180°
45°
90°

⇒ In which of these is reverse recovery time nearly zero?
Zener diode
Tunnel diode
Schottky diode
PIN diode

⇒ The oscillator frequency is set for
best picture
max. sound
min. sound
sound in picture

⇒ Wave A starts its positive half cycle at ωt = 30° and wave B starts its positive half cycle at ωt = 75° then wave B is leading wave A by 45°.
TRUE
FALSE

⇒ The current gain of a bipolar transistor drops at high frequencies because of
transistor capacitance
high current effects in the base
parasitic inductive elements
the early effect

⇒ A typical value of g_m for a FET is about 25 μs.
TRUE
FALSE

⇒ Two capacitors of 1 μF and 2 μF are connected in series across a 10 V dc battery. After the capacitors have been charged, the charges across the two capacitors will be
10 μC each
20 μC each
10 μC and 20 μC
20 μC and 10 μC

⇒ When a high voltage reference is required it is advantageous to use two or more zener diodes in series to allow
higher voltage
higher dissipation
lower temperature coefficient
all of the above

⇒ In a circuit containing a complex impedance, maximum power transfer takes place when load is
pure resistance
equal to the complex impedance
conjugate complex of the circuit impedance
none of the above

⇒ Tropospheric scatter is used with frequencies in the
HF
VHF
UHF
VLF

⇒ An RLC series circuit has Q = 100 and ω₀ = 20 rad/sec. The bandwidth is
0.2 rad/sec
2 rad/sec
20 rad/sec
2000 rad/sec

⇒ An interrupt in which the external device supplies its address as well as the interrupt is known as
vectored interrupt
maskable interrupt
polled interrupt
non-maskable interrupt

⇒ Consider the following statements:

If any root of characteristic equation has a positive real part the impulse response is unbounded and system is unstable.
If all the roots of a characteristic equation have negative real parts, the impulse response decays to zero.
If one or more non-repeated roots of characteristic equation are on jω axis impulse response is bounded but the system is unstable.

Which of the above equations are correct?
1, 2 and 3
1 and 2 only
1 and 3 only
2 and 3 only

⇒ In the given figure, of potentiometer V₀ = V_i (R₀/R_i) only
R_L = 0
R_L = ∞
R_L is neither low nor high
R_L is low but not zero