Question is ⇒ Which of the following methods gives the greatest breaking torque ?, Options are ⇒ (A) Regenerative braking, (B) Plugging, (C) Rheostatic braking, (D) None of the above., (E) , Leave your comments or Download question paper.

Question is ⇒ Which of the following methods gives the greatest breaking torque ?, Options are ⇒ (A) Regenerative braking, (B) Plugging, (C) Rheostatic braking, (D) None of the above., (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Which of the following methods gives the greatest breaking torque ?
A.	Regenerative braking [Wrong Answer]
B.	Plugging [Correct Answer]
C.	Rheostatic braking [Wrong Answer]
D.	None of the above. [Wrong Answer]
View Answer 5 -3 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which D.C. motor will be suitable alongwith flywheel for intermittent light and heavy loads?
Series motor
Shunt motor
Cumulatively compounded motor
Differentially compounded motor

⇒ The starting resistance of a D.C. motor is generally
low
around 500 ohms
1000 ohms
infinitely large

⇒ In the D.C. motor the iron losses occur in
the field
the armature
the brushes
the commutator

⇒ In a D.C. generator, the iron losses mainly take place in
yoke
commutator
armature conductors
armature rotor

⇒ Which of the following methods gives the greatest breaking torque ?
Regenerative braking
Plugging
Rheostatic braking
None of the above.

⇒ The direction of rotation of a D.C. series motor can be changed by
interchanging supply terminals
interchanging field terminals
either of (a) and (b) above
None of the above

⇒ In a motor, energy conversion would not have been possible but for the
production of opposing back e.m.f. Eb in the armature
input energy from supply
use of commutator
application of Fleming's left-hand rule

⇒ Ward-Leonard system of speed control is not recommended for
very low speeds
frequent motor reversals
wide speed range
constant speed operation

⇒ By looking at which part of the motor, it can be easily confirmed that a particular motor is D.C. motor?
Frame
Shaft
Commutator
Stator

⇒ The speed of a D.C. motor can be varied by varying
field current
applied voltage
resistance in series with armature
any of the above

⇒ If the field circuit of a loaded shunt motor is suddenly opened
torque developed by the motor would be reduced to zero
it would race to almost infinite speed
it would draw abnormally high armature current
the fuse or circuit breaker will open the circuit before too much damage is done to the motor

⇒ Which of the following load normally needs starting torque more than the rated torque?
Blowers
Conveyors
Air compressors
Centrifugal pumps

⇒ A D.C. motor can be easily identified by
winding
commutator
size of conductor
yoke

⇒ Which of the following method of speed control, of D.C. machine will offer minimum efficiency ?
Voltage control method
Field control method
Armature control method
All above methods

⇒ One D.C. motor drives another D.C. motor. The second D.C. motor when excited and driven
runs as a generator
does not run as a generator
also runs as a motor
comes to stop after sometime

⇒ Which of the following application requires high starting torque ?
Lathe machine
Centrifugal pump
Locomotive
Air blower

⇒ If the supply voltage for a D.C. motor is increased, which of the following will decrease ?
Starting torque
Operating speed
Full-load current
All of the above

⇒ If a D.C. shunt motor is working at full load and if shunt field circuit suddenly opens
this will make armature to take heavy current, possibly burning it
this will result in excessive speed, possibly destroying armature due to excessive centrifugal stresses
nothing will happen to motor
motor will come to stop

⇒ The losses occurring in a D.C. generator are given below. Which loss is likely to have highest proportion at rated load of the generator ?
hysteresis loss
field copper loss
armature copper loss
eddy current loss

⇒ Which of the following statement is incorrect ? If a starter is not used with large D.C. motor, it will draw a starting current which
will produce very low starting torque
will produce excessive line voltage drop
will damage the cOmmutator
is many times its full-load current

⇒ Which of the following losses are significantly reduced by laminating the core of a D.C. generator ?
Hysteresis losses
Eddy current losses
Copper losses
Windage losses

⇒ Which of the following motor is used in the locomotives motor drives ?
D.C. series motor
A.C. series motor
Synchronous motor
Induction motor

⇒ A 230 V D.C. shlint motor takes 32 A at full load. The back e.m.f. on full load, if the resistance of motor armature and shunt field windings are 0.2 Ω and 115 Ω respectively, will be
210 V
215 V
220 V
224 V

⇒ The speed regulation of a D.C. motor is

lowest speed

highest speed

highest speed - lowest speed

average speed

no-load speed - full-load speed

full-load speed

no-load speed - full-load speed

no-load speed

⇒ In case the back e.m.f. and the speed of a D.C. motor are doubled, the torque developed by the motor will
remain unchanged
reduce to one-fourth value
increase four folds
be doubled

⇒ Which of the following methods is most effective in finding out the no load losses in a large D.C. shunt motor ?
Field's test
Ward-Leonard test
Block rotor test
Swinburne's test

⇒ When the armature of a D.C. motor rotates, e.m.f. induced is
self-induced e.m.f.
mutually induced e.m.f.
back e.m.f.
none of the above

⇒ In which of the following applications D.C. series motor is invariably tried?
Starter for a car
Drive for a water pump
Fan motor
Motor operation in A.C. or D.C.

⇒ If the speed of a D.C. shunt motor is increased, the back e.m.f. of the motor will
increase
decrease
remain same
become zero

⇒ The total losses in a well designed D.C. generator of 10 kW will be nearly
100 W
500 W
1000 W
1500 W