Question is ⇒ Which of the following is used to obtain output position in a position control system?, Options are ⇒ (A) Strain gauge, (B) Load cell, (C) Synchro, (D) Thermistor, (E) , Leave your comments or Download question paper.

Question is ⇒ Which of the following is used to obtain output position in a position control system?, Options are ⇒ (A) Strain gauge, (B) Load cell, (C) Synchro, (D) Thermistor, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Which of the following is used to obtain output position in a position control system?
A.	Strain gauge [Wrong Answer]
B.	Load cell [Correct Answer]
C.	Synchro [Wrong Answer]
D.	Thermistor [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ For a logic fa
V_IH > V_0H > V_IL > V_0L
V_OH > V_IH > V_IL > V_0L
V_IH > V_OH > V_OL > V_IL
V_OH > V_IH > V_OL > V_IL

⇒ When a trivalent impurity is added, the semiconductor becomes
p type
n type
intrinsic
neutral

⇒ Which of the following statements regarding two transistor model of p-n-n-p device is correct?
It explain only the turn on portion of the device characteristics
It explain only the turn off portion of the device characteristics
It explain only the negative region portion of the device characteristics
It explain all the regions of the device characteristics

⇒ An op-amp integrating circuit uses
an inductor
a capacitor
both inductor and capacitor
none of the above

⇒ To measure a resistance by a dc potentiometer
it is necessary to standardise the potentiometer
it is not necessary to standardise the potentiometer
it is necessary to use a volt ratio box
none of the above

⇒ In LED the radiation is in
visible region
infrared region
both (a) and (b)
neither (a) nor (b)

⇒ In the periodic train of rectangular pulses F₀ = (V₀/T)d
TRUE
FALSE

⇒ The main systems used for generation of SSB are
filter method
phase cancellation method
third method
all of the above

⇒ A three-section RC phase shift oscillator has R = 10K ohms and C = 0.001 μF. The frequency of oscillations is
1.1 kHz
2.5 kHz
3.3 kHz
6.5 kHz

⇒ The sensor generally used in incremental optical encoder is
LED
LCD
photodiode
either (a) or (b)

⇒ Two voltages 50 V each have a phase difference of 45°. The rms value of resultant sum of the two voltages is
70.7 V
80.4 V
92.4 V
100 V

⇒ Consider the z-transform X(z) = 5z² + 4z^-1 + 3; 0 < |z| < ∞ The inverse transform x[n] is
5δ[n + 2] + 3δ[n] + 4δ[n - 1]
5δ[n - 2] + 3δ[n] + 4δ[n + 1]
5u[n + 2] + 3u[n] + 4u[n - 1]
5u[n - 2] + 3u[n] + 4u[n + 1]

⇒ FET amplifier is more difficult to analyse than BJT amplifier.
TRUE
FALSE

⇒ Which family of logic circuits uses field effect transistors?
TTL
CMOS
Both LED and well as LCD
None of the above

⇒ The current wave shown in figure is applied at t = 0 to a 0.1 F capacitor. At t = 1 s, the voltage across capacito
0 V
10 V
20 V
40 V

⇒ Degaussing in a picture tube means
Adding magnetism in mask and mounting frame
Removing residual magnetism in mask, shield etc...
Increasing resistance of coils to decrease time constant
Decreasing resistance of coils to increase time constant.

⇒ Electric breakdown strength of a material depends on its
composition
moisture content
thickness
all of the above

⇒ The power requirement of a RADAR used in military operations is
a few watts
about 500 W
about 2000 W
a few megawatts

⇒ In 8085
P flag is set when the result has even parity
P flag is set when the result has odd parity
P flag is reset when the result has odd parity
P flag is reset when the result has even parity

⇒ The noise figure of individual stages of a two stage amplifier is 2.03 and 1.54 respectively. If gain of first stage is 62, the overall noise figure is
2.03
2.055
3.05
6.05

⇒ Which is a digital coding technique?
PCM
DM
DPCM
All

⇒ For a sinusoidal input, the circuit shown in the figure will act
Pulse generator
Full wave rectifier
Ramp generator
Voltage Doubler

⇒ The relaxation time of electrons in a metal is of the order of
10^-6 secs
10^-10 secs
10^-14 secs
10^-20 secs

⇒ In a differential amplifier, CMRR can be improved by using an increased
emitter resistance
collector resistance
power supply voltages
source resistance

⇒ The unit of loudness is
phon
sone
decibel
mel

⇒ A 2 bit BCD D/A converter is a weighted resistor type with E_R = 1V, R = 1 MΩ and R_f = 10KΩ then Resolution in percent and volt is __________ .
1%, 1 mv
10%, 10 mv
10%, 1 mv
1%, 10 mv

⇒ Which TM mode in rectangular waveguide has lowest cutoff frequency?
TM₁₁
TM₀₁
TM₁₀
TM₂₁

⇒ The skip distance is
same for each layer
independent of frequency
independent of the state of ionisation
independent of transmitted power

⇒ In an R-L circuit excited by a battery of voltage E, the current and voltage across resistor are 1- e^-t and 2(1 - e^-t) respectively. If there were an initial current of 2 A in the inductance, the voltage across resistance would have been
1 - e^-t
2 - 2e^-t
2 + 2e^-t
4 - 4e^-t

⇒ In the given figure shows a periodic triangular wave. The Fourier series will
all cosine terms
all sine terms
odd cosine terms
odd sine terms

Users Also Read
Previous Papers

Aptitude

Reasoning

Gen.Knowledge

Speak English

English / Verbal

Online / Mock Test

Vedic Math