Question is ⇒ Which of the following is used in integrated circuits?, Options are ⇒ (A) Microstrip line, (B) Coaxial line, (C) Twin wire line, (D) Shield cable, (E) , Leave your comments or Download question paper.

Question is ⇒ Which of the following is used in integrated circuits?, Options are ⇒ (A) Microstrip line, (B) Coaxial line, (C) Twin wire line, (D) Shield cable, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Which of the following is used in integrated circuits?
A.	Microstrip line [Correct Answer]
B.	Coaxial line [Wrong Answer]
C.	Twin wire line [Wrong Answer]
D.	Shield cable [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ If h₁[n] = 3δ[n] + δ[n - 1], h₂[n] = 2δ[n] + δ[n
{6, 18, 7, 4, 0, - 6, 9}
{9, 0, - 6, 21, 7, 6, 1}
{7, - 1, 3, 1, 7, 0, 6}
{9, - 6, 0, 1, 21, 7, 18, 6}

⇒ A 12 bit ADC is used to convert analog voltage of 0 to 10 V into digital. The resolution is
2.44 mV
24.4 mV
1.2 V
none of the above

⇒ A piece of copper and another piece of Germanium are cooled from 30°C to 80 K. The resistance of
copper decreases and germanium increases
both decreases
both increases
copper increases and germanium decreases

⇒ For an ideal 3000 Hz channel, S/N ratio is
3
1.5
4
2

⇒

Match the following:

	List I		List II
A.	Former	1.	Produces deflecting torque
B.	Coil	2.	Provides base for coil
C.	Core	3.	Makes the magnetic field radial
D.	Spring	4.	Provides controlling torque

A-1, B-2, C-3, D-4
A-2, B-1, C-3, D-4
A-1, B-2, C-4, D-3
A-2, B-1, C-4, D-3

⇒ In 8085 microprocessor, the RST 5.5 interrupt service routine start from location
0020 H
0024 H
0028 H
002 CH

⇒

Match the following:

	List I (Logic)		List II (Characteristic)
A.	RTL	1.	High fan out
B.	CMOS	2.	Highest speed of operation
C.	I²L	3.	High noise immunity
D.	ECL	4.	Lowest product of power and delay

A-4, B-3, C-2, D-1
A-4, B-3, C-2, D-3
A-3, B-1, C-4, D-2
A-3, B-4, C-1, D-2

⇒ In an RC impedance function
the highest critical frequency is a pole
the highest critical frequency is a zero
the highest critical frequency is a pole or zero
the highest critical frequency is a pole at s = 0

⇒ The unit for luminous energy is
lumens/sec
lumens/m²
lumen-sec
lumen/m

⇒ Which one is a causal system?
y(n) = 3x[n] - 2x[n - 1]
y(n) = 3x[n] + 2x[n + 1]
y(n) = 3x[n + 1] + 2x[n - 1]
y(n) = 3x[n + 1] 2x[n - 1] + x[n]

⇒ Two ammeters A and B are connected in parallel in a circuit carrying 100 A. Their resistances are 0.8 mΩ. Their readings will be.
55.56 and 44.44 A respectively
44.44 A and 55.56 A respectively
60 A and 40 A respectively
40 A and 60 A respectively

⇒ In a transistor E mode the collector current with the transistor in cut off region is
zero
high
equal to saturated value
none of the above

⇒ In a shift left register, shifting a bit by one bit means
division by 2
multiplication by 2
subtraction of 2
None of the above

⇒ In an LC immittance H (s)
the slope of dH (jω)/dω is always negative
the slope of dH (jω)/dω is always positive
the slope of dH (jω)/dω may be positive or negative
the slope of dH (jω)/dω is constant

⇒ In following circuit, R_B will be if V_CC = 10 V, V_S = 2 V, R_C = 5 kΩ, R_S = 90 kΩ, β = 50, I_CE = 0, V_CEsat = 0
230 K
235 K
240 K
250 K

⇒ In a radio receiver with simple AGC
the highest AGC voltage is produced between stations
an increase in signal strength produces more AGC
the audio stage gain is normally controlled by AGC
the faster the time constant of AGC, more accurate the output

⇒ The carrier frequency will be if L = 50 µH and C = 1 nF.
512
612 kHz
712 kHz
812 kHz

⇒ In pulse code modulation when the maximum frequency in the signal is f_max the bandwidth required will be
≤ p.f_max
≥ p.f_max
≤ (p.f_max)²
≥ (p.f_max)²

⇒ Which junction transistor is preferred for high input and low output impedances?
Common emitter
Common base
Common collector
Any of the above

⇒ The work function of a photo surface whose threshold wave length is 1200 A, will be
0.103 eV
0.673 eV
1.03 eV
1.27 eV

⇒ A uniform plane wave in the free space is normally incident on an infinitely thick dielectric slab (dielectric constant ε_r = 9). The magnitude of the reflection coefficient is
0
0.3
0.5
0.8

⇒

Assertion (A): A thermocouple transducer is based on Seeback effect.

Reason (R): In a thermocouple transducer used for temperature measurement, the cold junction is usually kept in ice bath.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒ In a JK master slave flip flop
master is clocked when clock is low
slave is clocked when clock is high
master is clocked when clock is high and slave is clocked when clock is low
master is clocked when clock is low and slave is clocked when clock is high

⇒ The ratio of the directivity of an end fire antenna to that of a broadside antenna is
2
3
4
5

⇒ The circuit of the given figure
full adder
full subtractor
shift register
decade counter

⇒ If e = 10 sin(10⁸ t + 3 sin 10⁴ t) then the deviation is
4.77 kHz
47.7 kHz
477 kHz
4770 kHz

⇒ Poynting theorem relates the electric intensity E, magnetic intensity H to the rate of energy flow per unit area at a point P as
P = E/H
P = H/E
E = 1/E x H
P = E x H

⇒ Resistivity of electrical conductors is most affected by
Pressure
temperature
composition
ageing

⇒

Assertion (A): Thevenin's theorem and Norton's theorem are dual of each other.

Reason (R): Voltage source can be converted into current source and vice versa.

Both A and R are true and R is correct explanation of A
Both A and R are true and R is not the correct explanation of A
A is true but R is false
A is false but R is true

⇒ In a rectifier circuit the filter capacitance is increased. Then the ripple will
increase
decrease
remain the same
either (a) or (b)