Question is ⇒ Which of the following is not valid in case of bipolars?, Options are ⇒ (A) It has a low input impedance, (B) It has high voltage gain, (C) It is a current controlled device, (D) It is difficult to bias, (E) , Leave your comments or Download question paper.

Question is ⇒ Which of the following is not valid in case of bipolars?, Options are ⇒ (A) It has a low input impedance, (B) It has high voltage gain, (C) It is a current controlled device, (D) It is difficult to bias, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Which of the following is not valid in case of bipolars?
A.	It has a low input impedance [Wrong Answer]
B.	It has high voltage gain [Wrong Answer]
C.	It is a current controlled device [Wrong Answer]
D.	It is difficult to bias [Correct Answer]
View Answer 1 -1 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which is known as flash converter?
Weighted resistor D/A converter
Parallel A/D converter
Stair step A/D converter
Up-down counter type A/D converter

⇒ In 8085 eight address and data buses are multiplexed.
TRUE
FALSE

⇒ An air gap provided in the iron core of an inductor prevents
flux leakage
hysteresis loss
core saturation
heat generation

⇒ Virus is a
computer hardware problem
an operating system
a computer program
a computer language

⇒ Which of the following can be used to isolate a low impedance from a high impedance source?
Emitter follower
p filter
Darlington pair
Any of the above

⇒ In common base configuration, the input characteristics of bipolar junction transistor are drawn between
V_EB and I_E
V_CB and I_C
I_C and V_CE
I_E and V_CE

⇒ The virtual height of an ionospheric layer is __________ true height
equal to
less than
higher than
no relation

⇒ An ideal op-amp can amplify dc signals
TRUE
FALSE

⇒ Consider the following statements as regards induction and dynamometer wattmeters

Dynamometer wattmeters can be used for dc only.
Induction wattmeter has higher torque and dynamometer wattmeter.
Induction wattmeter is less accurate, has more power consumption and more weight than dynamometer wattmeter.

Which of the above statements are correct?
1 only
1 and 2 only
2 and 3 only
1 and 3 only

⇒ In a commercially available good power supply the voltage regulation is about
0.01
0.05
0.1
0.2

⇒ For a photoconductor with equal electron and hole mobilities and perfect ohmic contacts at the ends, an increase in illumination results in
a change in O.C. voltage
a change in S.C. current
a decrease in resistance
an increase in resistance

⇒ Dielectric loss due to polarisation occurs in
bipolar dielectrics
non-metallic dielectrics
liquid dielectrics
all of the above

⇒ Consider the following stateme
1 and 2
2 and 3
3 and 4
4 and 5

⇒ The first machine cycle of an instruction is always
a memory read cycle
a fetch cycle
a input/output read cycle
a memory write cycle

⇒ Which of the following is not an integer constant?
2.3
156231
10
-256

⇒ TM₀₁ mode in circular waveguide is analogous to
TM₁₀ mode in square waveguide
TM₁₁ mode in square waveguide
TM₂₀ mode in square waveguide
TM₀₂ mode in square waveguide

⇒ 100101₂ is equal to decimal number
47
37
21
17

⇒ In a simple on-off controller with differential gap, the magnitude of differential gap determines
the level of accuracy
the life of controller
both (a) and (b)
neither (a) nor (b)

⇒ The number of digits in hexadecimal system
15
16
10
8

⇒ A linear time-invariant, causal continuous time system has a rational transfer function with simple poles at s = - 2 and s = - 4, and one simple zero at s = - 1. A unit step u(t) is applied at the input of the system. At steady state, the output has constant value of 1. The impulse response of this system is
[exp (- 2t) + exp (-4t)] u(t)
[-4 exp (- 2t) + 12 exp (-4t) - exp (-t)] u(t)
[-4 exp (- 2t) + 12 exp (-4t)] u(t)
[-0.5 exp (- 2t) + 1.5 exp (-4t)] u(t)

⇒ In figure (A) and
A represents PCM and B represents AM
A represents FM and B represents AM
A represents AM and B represents FM
A represents PCM and B represents FM

⇒ Audio frequency range lies between
20 Hz and 20 kHz
20 kHz and 20 MHz
2 MHz and 20 MHz
20 MHz and 200 MHz

⇒ Measurement of hall coefficient enables the determination of
mobility of charge carriers
type of conductivity and concentration of charge carriers
temperature coefficient and concentration of charge carriers
fermi level and forbidden energy gap

⇒ A single phase full converter gives maximum and minimum output voltage at firing angles of
0 and 180° respectively
180° and 0° respectively
0 and 90° respectively
90° and 0° respectively

⇒

Assertion (A): Tie set schedule is used in nodal analysis.

Reason (R): Loop currents are fictitious quantities.

Both A and R are true and R is correct explanation of A
Both A and R are true and R is not the correct explanation of A
A is true but R is false
A is false but R is true

⇒ Determine the voltage V_CB in the circuit bel
3.4 V
5.4 V
7.4 V
9.4 V

⇒ A 1 μF capacitor is connected to 12 V battery. The energy stored in the capacitor is
12 x 10^-6 J
24 x 10^-6 J
48 x 10^-6 J
72 x 10^-6 J

⇒ Consider the following

Maximum energy of electrons liberated photoelectrically is independent of light intensity
Maximum energy of electrons liberated photoelectrically varies nonlinearly with frequency of incident light.

(1) is true and (2) is false
(1) and (2) both are true
(1) is false and (2) is true
(1) and (2) both are false

⇒ What is the numerical aperture an optical fiber when critical angle is 30°?
0.5
0.704
0.866
0.2

⇒ An RC driving point impedance function has zeros at s = - 2 and s = - 5. The admissible poles are
s = 0 and s = -6
s = -1 and s = -3
s = 0 and s = -1
s = -3 and s = -4