Question is ⇒ Which of the following is not necessarily the advantage of SSB over double sideband, full carrier AM?, Options are ⇒ (A) The signal is more noise resistant, (B) More channel space is available, (C) Transmitter circuits must be more stable, given better reception, (D) Considerably less power is required for the same signal strength, (E) , Leave your comments or Download question paper.

Question is ⇒ Which of the following is not necessarily the advantage of SSB over double sideband, full carrier AM?, Options are ⇒ (A) The signal is more noise resistant, (B) More channel space is available, (C) Transmitter circuits must be more stable, given better reception, (D) Considerably less power is required for the same signal strength, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Which of the following is not necessarily the advantage of SSB over double sideband, full carrier AM?
A.	The signal is more noise resistant [Wrong Answer]
B.	More channel space is available [Wrong Answer]
C.	Transmitter circuits must be more stable, given better reception [Correct Answer]
D.	Considerably less power is required for the same signal strength [Wrong Answer]
View Answer 2 -2 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ If a sample of germanium and a sample of silicon have the same impurity density and are kept at room temperature
both will have equal value of resistivity
both will have equal negative resistivity
resistivity of germanium will be higher than that of silicon
resistivity of silicon will be higher than that of germanium

⇒ In figure gain bandwidth produc
200 Hz
200 MHz
200 kHz
2 MHz

⇒ An op-amp uses
RC coupling
direct coupling
transformer coupling
either (b) or (c)

⇒ For most static RAM the write pulse width should be at least
10 ns
60 ns
300 ns
1 μs

⇒ In a N-P-N transistor, when emitter junction is forward biased and collector junction is reverse biased the transistor will operate in
active region
saturation region
cut-off region
inverted region

⇒ Calculate cut off frequency for dominant mode in rectangular waveguide if dimensions are a = 2, b = 1 cm.
7.5 GHz
1.5 GHz
15 GHz
150 GHz

⇒ The logic circuit given below converts a binary code y₁ y₂, y₃
Excess - 3 code
Gray code
BCD code
Hamming

⇒

Assertion (A): The conductivity of p type semiconductor is higher than that of intrinsic semiconductor.

Reason (R): The addition of donor impurity creates additional energy levels below conduction band.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ n type semiconductors
are negatively charged
are produced when indium as impurity is added to germanium
are produced phosphorus as impurity is added to silicon
none of the above

⇒ In a DM system, the granular noise occurs when modulating signal
decrease Rapidly
increase
has high frequency component
change within step size

⇒ As the temperature of an intrinsic semiconductor material is increased
additional holes are created in the conduction band
protons get excited
protons acquire charge
energy of the atom is increased

⇒ A linear system is characterized by H(ω) = Be^-2ω² the system is physically
unrealizable
realizable
depends upon B
depends upon constant 2

⇒ Consider the following statements about DRAM

Page mode read operation is faster than RAS read
RAS input remains active during column address strobe
The row and column addresses are strobed into the internal buffers using RAS and CAS inputs respectively

Which of the above statements are correct?
1 and 3 only
All
1 and 2 only
2 and 3 only

⇒ Bus bars are always meant for very heavy currents.
TRUE
FALSE

⇒ In 8085 microprocessor, in order to enable INTR interrupt, which of the following instruction are needed?
EI only
SIM only
El and SIM both
None

⇒ Which of the following statements is incorrect?
A mesh with two resistors has two mesh currents
The algebraic sum of all voltages around any mesh or any loop must be zero
The principle node is a function where branch current can divide or combine
A Norton is a series circuit

⇒ When temperature is above ferromagnetic Curie temperature, a ferromagnetic material
becomes a paramagnetic material
becomes a very strong ferromagnetic material
becomes diamagnetic material
none of the above

⇒ Which power amplifier can deliver maximum load power?
Class A
Class AB
Class B
Class C

⇒ Low gain-bandwidth product of a JFET is due to
reduced number of holes
junction capacitive effects
low degree of isolation between input and output
all of the above

⇒ Saturation region of a JFET is also known as
source region
analog region
pinch off region
ohmic region

⇒ In a minimum phase system
all poles lie in the left half plane
all zeros lie in the left half plane
all poles lie in the right half plane
all except one pole or zero lie in the left half plane

⇒ In force voltage analogy, displacement is analogous to
current
voltage
charge
none of the above

⇒

Assertion (A): In AM carrier component remains constant in amplitude and frequency.

Reason (R): In AM the two side bands are images of each other.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ Octal 16 is equal to decimal
13
14
15
16

⇒ An electron in a homogeneous magnetic field and having velocity perpendicular to the direction of field moves
perpendicular to the field
along the field
along a straight line inclined at 45° to field
in a circular path

⇒ The first column of a Routh arra
2
3
4
5

⇒ A source is delivering maximum power to a resistance through a network. The ratio of power delivered to the source power,
is always 0.5
may be 0.54 or less
may be 0.5 or less
may be 0.5 or more

⇒ A FET is to be operated as voltage variable resistor. For this drain to source voltage V_DS should be,
74
= V_P
< V_P
> V_P

⇒ The average load current supplied by a thyristor depends on
firing angle
firing frequency
magnitude of gate current
all of the above

⇒ The symbol in figure is
SUS
SBS
SCS
None of the above