Question is ⇒ Which of the following is not a valid real constant?, Options are ⇒ (A) -73.1, (B) 10251,3, (C) 10.23, (D) -5.7381, (E) , Leave your comments or Download question paper.

Question is ⇒ Which of the following is not a valid real constant?, Options are ⇒ (A) -73.1, (B) 10251,3, (C) 10.23, (D) -5.7381, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Which of the following is not a valid real constant?
A.	-73.1 [Wrong Answer]
B.	10251,3 [Correct Answer]
C.	10.23 [Wrong Answer]
D.	-5.7381 [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which of the following are applications of position control systems?
Control of sheet and metal thickness in hot rolling mill
Missile guidance of ships
Radar tracking system
All of the above

⇒ The number of roots of s³ + 2s² + 7s + 3 = 0 in the left half of the s-plane is :
zero
one
two
three

⇒ As the temperature of a pure silicon specimen is increased
the number of free electrons increases
the number of holes decreases
the number of holes increases
the number of free electrons and holes increases

⇒ An image uses 512 x 512 picture elements. Each of the picture elements can take any of the 8 distinguishable intensity levels. The maximum entropy in the above image will be
2097152 bits
648 bits
786432 bits
144 bits

⇒ At night D layer of ionosphere is absent.
TRUE
FALSE

⇒ Which of the following is necessary transistor action?
The base region must be very wide
The base region must be very narrow
The base region must be made of some insulating material
The collector region must be heavily doped

⇒ Waveform shown in figure is that
FM
PCM
AM-DSB
AM-SSB

⇒ The permanent magnet field system of brushless dc servo- motor is generally on
stator
rotor
partly on stator and partly on rotor
either (a) or (b)

⇒ The accumulator drives the ALU.
TRUE
FALSE

⇒ The boundary conditions at the interface between two dielectrics in an electric field are given by
D_normal = 0, E_tangential = 0
D_normal = 0, E_normal = 0
D_tangential = 0, E_tangential = 0
D_tangential = 0, E_normal = 0

⇒ Two currents have the same peak value. Wave 1 is sinusoidal and wave 2 is rectangular. The ratio of their heating effects are
0.0423611111111111
1 : 2
0.0430555555555556
0.000711805555555555

⇒ To turn off an SCR, it is necessary to reduce its current to less than :
trigger current
holding current
breakover current
none of the above

⇒ Choose the correct match for input resistance of various amplifier configurations shown below configurat
CB-LO, CC-MO, CE-HI
CB-LO, CC-HI, CE-MO
CB-MO, CC-HI, CE-LO
CB-HI, CC-LO, CE-MO

⇒ Figure shows four D type FFs are connected as a shift register using an XOR gate. The initial state and 3 subsequent states for 3 clock pulses are also g
0
1111
1001
1000

⇒

Assertion (A): A p-n junction is used as rectifier.

Reason (R): A p-n junction has low resistance in forward direction and high resistance in reverse direction.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ Which of the following devices has two gates?
SCR
SCS
SUS
SBS

⇒ EEPROM is also known as
UVPROM
EAPROM
both UVPROM and EAPROM
none of the above

⇒ If V_dc1 is the dc output voltage in half wave controlled rectifier circuit feeding resistive load and V_dc2 is the dc output voltage in full wave controlled rectifier circuit (M - 2 connection) feeding resistive load, then
V_dc1 = 0.5 V_dc2 for all values of firing angle
V_dc1 = V_dc2 for all values of firing angle
V_dc1 ≤ 0.5 V_dc2 for all values of firing angle
V_dc1 ≥ 0.5 V_dc2 for all values of firing angle

⇒ In a pneumatic bellows
the input surface, output surface and side walls are corrugated
the input surface and output surface are flat but the side walls are corrugated
the input surface and side walls are flat but the output surface is corrugated
the input surface and output surface are corrugated but the side walls are flat

⇒ For a = - 1, find the value of V_{2∞
0
V₁
none of the above}

⇒ In p type semiconductor, the hole concentration
is nearly equal to density of acceptor atoms
is much greater than density of acceptor atoms
is much less than density of acceptor atoms
may be equal to or more or less than density of acceptor atoms

⇒ A 0 to 6 counter consist of 3 flip-flop and a combinational circuit of 2 input gates. The combinational circuit consist of
one AND gate
one OR gate
one AND and One OR
two AND gate

⇒ The coding system generally used in digital telemetry is
PPM (Pulse position modulation)
PAM (Pulse amplitude modulation)
PCM (Pulse code modulation)
PDM (Pulse duration modulation)

⇒ In low power factor wattmeter, the pressure coil is connected
to the supply side of current coil
to the load side of current coil
in either (a) or (b)
across the mains

⇒ A sine wave is passed through an amplifier which severely limits it symmetrically. If then passes to a second amplifier which is narrow band and tuned to the frequency of the original sine wave. What will be the output wave from this second amplifier?
A square wave of the same frequency as that of the original sine wave
A square wave of double the frequency of that of original sine wave
A sine wave of constant amplitude at the frequency of the original sine wave
A sine wave of constant amplitude at double frequency of the original sine wave

⇒ The units of F(jω) are volt-seconds.
TRUE
FALSE

⇒ In MF range, increasing the transmitter power
increases the range of transmitter
does not increase the range of transmitter because propagation is limited by tilt
decreases the range of transmitter because propagation is limited by tilt
increases the range of transmitter because propagation is through space waves

⇒ The h parameter h₁₁ is the same in CE and CC circuit.
TRUE
FALSE

⇒ A digital voltmeter has a read out range from 0 to 999 counts. If the full scale reading is 9.999 V, the resolution is
1 V
0.01 V
1 mV
1 μV

⇒ A signal m(t) = 5 cos 2p 100 t frequency modulates a carrier. The resulting FM signal
0.1 kHz
6 kHz
3.2 kHz
100 kHz