Question is ⇒ Which of the following is not a condensation polymer ?, Options are ⇒ (A) Bakelite, (B) Melamine polymer, (C) Polymethylmethacrylate (PMMA), (D) None of these, (E) , Leave your comments or Download question paper.

Question is ⇒ Which of the following is not a condensation polymer ?, Options are ⇒ (A) Bakelite, (B) Melamine polymer, (C) Polymethylmethacrylate (PMMA), (D) None of these, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Which of the following is not a condensation polymer ?
A.	Bakelite [Wrong Answer]
B.	Melamine polymer [Wrong Answer]
C.	Polymethylmethacrylate (PMMA) [Correct Answer]
D.	None of these [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Thiokol is nothing but
polysulphide rubber
polyamide fibre
engineering plastic
exponded polystyrene

⇒ Terylene is
same as dacron
a polyester
both(a) & (b)
neither (a) nor (b)

⇒ Non sulphonated hard bakelites are not used for making
ion-exchange resins
fountain pen barrels
formica table tops
combs

⇒ Phenol formaldehyde is produced by condensation polymerisation. It is also known as
teflon
bakelite
polyester
nylon-66

⇒ Zeigler process
produces high density polythene.
uses no catalyst.
produces low density polythene.
employs very high pressure.

⇒ Density of low density polythene is about __________ gm/c.c.
0.38
0.56
0.81
0.91

⇒ Polypropylene compared to polythene is
harder
stronger
lighter
all (a), (b) and (c)

⇒ The monomer of natural rubber is
DMT
isoprene
2 methyl-1-propene
both (b) and (c)

⇒ Addition polymerisation is not involved in the manufacture of
low density polythene.
poly vinyl chloride.
polystyrene.
polyhexamethylene adipamide.

⇒ Alkyd resin can not be used for making
plasticiser
paint & varnish
fibres
film forming materials

⇒ Synthetic rubber
deforms, if stretched to double of its original dimension.
is brittle at low temperature
is softer at higher temperature.
is highly permeable to air & water and is readily attacked by chemicals & atmospheric gases.

⇒ Which of the following is a natural polyamide fibre.
Wool
Silk
Cotton
None of these

⇒ Which of the following is a copolymer ?
Polystyrene
SBR
P.T.F.E.
Polypropylene

⇒ Polycondensation of saturated dicarboxylic acid with polyhydric alcohol produces
epoxy resin
polyamide
alkyd resin
phenolic resin

⇒ Low pressure Zeigler process of polythene manufacture
employs a pressure of 30 kgf/cm².
achieves an yield of 95-98% based on ethylene.
produces very low density polythene.
does not use any catalyst for polymerisation.

⇒ Rayon is a __________ fibre.
cellulosic
polyamide
polyester
natural

⇒ A copolymer of vinyl and vinylidine chloride is called
treylene
orlon
saran
dacron

⇒ Identify the group in which all the polymers mentioned can be used to make fibres.
Butadiene copolymers, Polyamides, Urea aldehyde
Cellulose derivatives, Polyisoprene, Polyethylene
Cellulose derivatives, Polyamides, Polyurathane
Polypropylene, Poly vinyl chloride, Silicon

⇒ Main constituent of cotton fibre is
lignin
cellulose
starch
gelatine

⇒ Typical solvent polymerisation reaction conditions for the production of high density polythene by Zeigler process is
7 kgf/cm² and 70 °C.
1000 kgf/cm² and 100°C.
7 kgf/cm² and 700°C.
1 kgf/cm² (gage) and 70°C.

⇒ Pick out the wrong statement.
Denier is defined as weight in gm of 9000 metres length of a fibre, while tex is defined as weight in gm of 1000 metres length of fibre.
Crimp is a measure of the difference between the length of the straightened and unstraightend fibre.
Dacron fibres, acrylic fibres, viscose rayon fibres & cellulose acetate fibres are all prepared by wet spinning.
Nylon fibres have greater water absorption capacity than polyester fibres.

⇒ Viscosity of a polymer solution or melt
decreases with increase in molecular weight.
decreases with increase in temperature.
increases with increase in temperature.
does not vary with temperature rise.

⇒ The conversion of caprolactum in the above case is about __________ percent.
25
50
70
90

⇒ Nylon 6, 10 which is used for bristles making is superior to nylon 6, 6 due to its lower water absorption capacity, is a/an
polyester
polyamide
polyisoprene
polystyrene

⇒ In nylon-6, the number 6 represents the total number of
carbon atoms in the ring.
carbon atoms in the linear polymer chain.
nitrogen atoms in the ring.
hydrogen atoms in the ring.

⇒ __________ is normally used for the manufacture of refrigerator components and transistor parts.
Polyproylene
Polystyrene
Polyester
Polyurathene

⇒ Polymerisation product of C₂F₄ (carbon tetraflouride) is called P.T.F.E. (poly chloro tetra flouro ethylene). It is also called
polyurethane
silicone rubber
teflon
epoxy resin

⇒ Valcunisation of rubber decreases its
tensile strength.
resistance to organic solvents.
tackiness.
working temperature range.

⇒ Neoprene is rendered non-inflammable, because of
its cross-linked structure.
its linear chain structure.
the presence of chlorine atoms in its monomer.
the absence of chlorine atoms in its monomer.

⇒ Which of the following polymers has the tendency of decomposing before melting ?
Polystyrene
Nylon
PVC
None of these