Question is ⇒ Which of the following is a valid real constant?, Options are ⇒ (A) -81.56, (B) 73, (C) 10254,1, (D) 42, (E) , Leave your comments or Download question paper.

Question is ⇒ Which of the following is a valid real constant?, Options are ⇒ (A) -81.56, (B) 73, (C) 10254,1, (D) 42, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Which of the following is a valid real constant?
A.	-81.56 [Correct Answer]
B.	73 [Wrong Answer]
C.	10254,1 [Wrong Answer]
D.	42 [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The strength of controlled voltage source depends on
value of current elsewhere in the circuit
value of voltage elsewhere in the circuit
value of current or voltage elsewhere in the circuit
none of the above

⇒ One limitation of constant k filters is that Z₀ is not constant in the pass band.
TRUE
FALSE

⇒ Which of the following integer expressions is incorrect in Pascal?
L div M + P
A * * B
A div B - C
A mod B

⇒ In an op-amp comparator, the positive or negative output is
saturated
amplifier
unsaturated
any of the above

⇒ The minimum decimal equivalent of the number 11C0 is
183
194
268
269

⇒ Which of the following amplifiers has highest output impedance?
CE
CB
CC
Push pull

⇒ A feedback network to be used with an amplifier to provide oscillation is tested and found to give an output of 0.124 V with a 0.5 V input. What percentage negative feedback should be introduced to the amplifier so that linear oscillations result?
0.0125
0.025
-0.0125
-0.025

⇒ Which one of the following bipolar transistors has the highest current gain bandwidth Product (f_r) for similar geometry?
NPN germanium transistor
NPN silicon transistor
PNP germanium transistor
PNP silicon transistor

⇒ If a line is terminated in characteristic impedance Z₀, the input impedance measured at the input will be
Z₀
Z₀/2
Zero
infinite

⇒ A generated voltage is equally dependent on three resistances R₁, R₂, R₃ and its value is V = (R₁R₂)/R₃. If tolerance of each resistor is 0.1%, the maximum error in voltage is
0.003
± 0.3%
0.001
± 0.1%

⇒ The resistance of a bulb at the time of full brightness is 1200 Ω. Then the resistance at room temperature is about
1200 Ω
120 Ω
600 Ω
10 Ω

⇒ In an LC immittance H (s)
the slope of dH (jω)/dω is always negative
the slope of dH (jω)/dω is always positive
the slope of dH (jω)/dω may be positive or negative
the slope of dH (jω)/dω is constant

⇒

Assertion (A): In a BJT, a_dc is about 0.98.

Reason (R): In a BJT, recombination in base region is high.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ In the generic microprocessor
instruction cycle time period is shorter than machine cycle time period
machine cycle time period is shorter than instruction cycle time period
instruction cycle time period is exactly half of machine cycle time period
instruction cycle time period is exactly equal to machine cycle time period

⇒ The interface chip for 8086 and 16 bit ADC is
8259
8255
8253
8251

⇒ In an amplifier if conductor during the cycle is from 0 to 90° and again from 180° to 270°, the amplifier will be termed as
class A
class B
class C
class AB

⇒ Consider the following statements about polar plots

Addition of a non-zero pole to a transfer function results in further rotation of polar plot through an angle of - 90° as ω → ∞
Addition of a pole at the origin to a transfer function rotates the polar plot at zero and infinite frequencies by a further angle of - 90°

Of the above statements:
Both are correct
Both are wrong
1 is correct and 2 is wrong
2 is correct and 1 is wrong

⇒ The following graph, the number of trees (P) and the number of cut-sets (Q)
P = 2, Q = 2
P = 2, Q = 6
P = 4, Q = 6
P = 4, Q = 10

⇒

Assertion (A): In liquids and glassy substances, dielectric losses occur.

Reason (R): The orientation polarization in many substances is frequency dependent.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true

⇒ Which of the following material can be used in cable shields?
Copper
Aluminium
Cast iron
Lead

⇒ The circuit shown depic
voltage series negative feedback
voltage shunt negative feedback
current series negative feedback
current shunt negative feedback

⇒ Ohm's law is valid for
dc voltage and current
ac voltage and current
all voltages and current
dc and ac voltages and currents

⇒ A 10 bit D/A converter gives a maximum output of 10.23 V. The resolution is
10 mV
20 mV
15 mV
25 mV

⇒ The noise margin of a TTL gate is about
0.2 V
0.4 V
0.6 V
0.8 V

⇒ Two sinusoidal signals of equal amplitude and frequency are applied to X and Y plate of CRO respectively. The observed Lissajous pattern is a straight line. The phase shift between signals is
zero
90°
either zero or 180°
either 90° or 270°

⇒ In the above case the total power in the modulated wave double sideband, suppressed carrier AM will be
112 W
400 W
415 W
512 W

⇒ If (225)_Y = (165)₈ find value of Y
7
8
9
11

⇒

Assertion (A): FM requires more bandwidth than AM

Reason (R): Wide band FM is used for broadcast transmissions.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ Circular polarization
is useful in reducing depolarization effect on received wave
involves critical alignment of transmitting and receiving antenna
is useful in discrimination between reception of adjacent beams
none of the above

⇒

Assertion (A): If the reading of an instrument is low, the error is large.

Reason (R): The error of an instrument is certain percentage of its full scale deflection.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true