Question is ⇒ Which of the following equipment is used for arc welding generally used for arc welding ?, Options are ⇒ (A) Single phase alternator, (B) Two phase alternator, (C) Three phase alternator, (D) Transformer, (E) , Leave your comments or Download question paper.

Question is ⇒ Which of the following equipment is used for arc welding generally used for arc welding ?, Options are ⇒ (A) Single phase alternator, (B) Two phase alternator, (C) Three phase alternator, (D) Transformer, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Which of the following equipment is used for arc welding generally used for arc welding ?
A.	Single phase alternator [Wrong Answer]
B.	Two phase alternator [Wrong Answer]
C.	Three phase alternator [Wrong Answer]
D.	Transformer [Correct Answer]
View Answer 9 -7 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which of the following is not an inert gas ?
Argon
Helium
Carbondioxide
All of above

⇒ The power factor of a spot welding machine is expected to be around
Unity
0.8 lagging
0.3 to 0.5 lagging
0.8 leading

⇒ Helium produces which of the following?
Deeper penetration
Faster welding speedsNarrower heat affected zone in base metal
Narrower heat affected zone in base metal
All of the above

⇒ Motor-generator set for D.C. arc welding has generator of
series type
shunt type
differentially compound type
level compound type

⇒ For arc welding current range is usually
10 to 15A
30 to 40 A
50 to 100 A
100 to 350 A

⇒ In D.C. arc welding
electrode is made positive and work- piece negative
electrode is made negative and workpiece positive
both electrode as well as workpiece are made positive
both electrode as well as workpiece are made negative

⇒ ____ welding is not a resistance welding process.
Projection
Seam
Flush
Carbon arc

⇒ Air craft body is
spot welded
gas welded
seam welded
riveted

⇒ During spot welding the current flows for
fraction of a minute to several minutes
fraction of a second to several seconds
few milliseconds
few microseconds

⇒ For the welding of aluminium alloys which of the following methods would you recommend ?
Acetylene-oxygen gas welding
D.C. arc welding
A.C. arc welding
Tungsten arc welding

⇒ In arc welding major personal hazards are
flying sparks
weld spatter
harmful infrared and ultra-violet rays from the arc
all of the above

⇒ Which of the following is net a welding accessory ?
Hand screen
Cable
Electrode holder
Gloves

⇒ Plain and butt welds may be used on materials upto thickness of nearly
5 mm
10 nam
25 mm
50 mm

⇒ During resistance weldingheat produced at the joint is proportional to
I²R
kVA
current
Voltage

⇒ Electric arc welding process produces temperature upto
1000°C
1500°C
3500°C
5550°C

⇒ Resistance welding cannot be used for
dielectrics
ferrous materials
non-ferrous metals
any of the above

⇒ Steel rails are welded by
Gas welding
Thermit welding
Resistance welding
Argon arc welding

⇒ Which of the following automatic welding processes is likely to give maximum rate of metal deposition ?
Continuous flux covered electrode
Multiple power submerged arc
Gas shielded bare wire
Submerged arc (single wire)

⇒ The welding electric circuit is
never earthed
always earthed
through cables only

⇒ Grey iron is usually welded by ____ welding
gas
arc
resistance
MIG

⇒ Percent duty cycle of a welding machine means
machine input is 50 percent of rated input
machine efficiency is 50 percent
machine works on 50 percent output
machine works for 5 minutes in a duration of 10 minutes

⇒ TIG welding is
thorium iodine gas welding
thermally induced gas welding
temperature insulated gas welding
tungsten inert gas welding

⇒ In spot welding composition and thickness of the base metal decides
the amount of squeeze pressure
hold time
the amount of weld current
all above

⇒ In electrical resistance welding the greatest resistance is offered by which of the following ?
Metal surface
Contact point of electrode with metal top
Contact point of electrode with metal bottom
Contact layer o f meta ls to be welded

⇒ Which of the following electrodes will have leastliameter ?
20 SWG
16 SWG
14 SWG
4 SWG

⇒ A rectifier for welding has voltage/current characteristic as
static
variable
drooping
rising

⇒ Flux used in TIG welding is
borax
ammonium chloride
ash
none

⇒ The tips of the electrodes, for spot welding, are made of
copper alloy
porcelain
mica
carbon

⇒ The danger of shock is maximum
before welding
after arcing
during arcing
while inserting electrode into the holder

⇒ In atomic hydrogen welding the electrode is made of
carbon
graphite
tungsten
mild steel