Question is ⇒ Which of the following devices has a silicon dioxide layer?, Options are ⇒ (A) NPN transistor, (B) Tunnel diode, (C) JFET, (D) MOSFET, (E) , Leave your comments or Download question paper.

Question is ⇒ Which of the following devices has a silicon dioxide layer?, Options are ⇒ (A) NPN transistor, (B) Tunnel diode, (C) JFET, (D) MOSFET, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Which of the following devices has a silicon dioxide layer?
A.	NPN transistor [Wrong Answer]
B.	Tunnel diode [Wrong Answer]
C.	JFET [Wrong Answer]
D.	MOSFET [Correct Answer]
View Answer 1 -1 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ A rectifier voltmeter using bridge rectifier and PMMC meter is calibrated to read rms value of sine wave. A triangular wave is applied to it and it reads 6.82 V. The rms value of triangular wave is
about 6.82 V
about 7.1 V
about 6.5 V
about 10 V

⇒ A wire strain gauge has a gauge factor of 2, resistance of 125 Ω and length 1 m. If length of wire changes by .005 m, change in resistance will be
0.25 Ω
0.5 Ω
1.25 Ω
2.5 Ω

⇒ Which of the following oscillators is used for the generation of high frequencies?
R-C phase shift oscillator
Wien bridge oscillator
L-C oscillator
Blocking oscillator

⇒ In a Communication system, noise is most likely to affect the signal.
at the transmitter
In the channel
in Information source
at the destination

⇒ In the circuit of figure, the load current when thyristor is
is constant
increases exponentially
decreases exponentially
zero

⇒ The measure of mismatch between the load and the transmission line is known as
directivity
Gain
standing wave ratio
reflection coefficient

⇒ Which of the following is not a proper FORTRAN expression?
B + A / C - D
(A + C) / (B + D)
B + * A / C
A ** (B + 2)

⇒ The total number of channels allotted for cellular telephone is
666
333
221
111

⇒ A 1 ms pulse can be converted into a 10 ms pulse by using which one of the following
An astable multivibrator
Stable multivibrator
A bistable multivibrator
A J-K flip-flop

⇒ If sequence currents I_a1 = 2 ∠- 90°, I_a2 = 0.2 ∠ 90° and I_a3 = 1.8 ∠ 90°, I_a =
0
1
4
8

⇒ A higher value of Standing Wave Ratio indicates
least mismatch between line and load
greater mismatch between load and line
number of nodes is equal to the number of antinodes
none of the above

⇒ The drain characteristics of JFET in operating region, are
inclined upwards
almost flat
inclined downwards
inclined upwards or downwards

⇒ Which synthesis procedure requires the use of mutual inductance?
Foster's synthesis
Cauer synthesis
Bott-Duffin synthesis
Brune's synthesis

⇒ To relay outdoor remotely located live programs, TV transmitter use
microwave links
coaxial cable link
open wire link
either (b) or (c)

⇒ LET JCOKE = 11 and LPEPSI = 19. Consider the statement 13
16
9
14

⇒ An oscilloscope has an input impedance consisting of 1 MΩ and 20 pF is parallel. A high impedance probe connected to input of this oscilloscope has a 10 MΩ series resistance. This 10 MΩ series resistance
may not be shunted
should be shunted by 2 pF capacitor
should be shunted by 20 pF capacitor
should be shunted by 200 pF capacitor

⇒ Half wave sysmmetry means f(t) = - f(t ± T/2).
TRUE
FALSE

⇒ The applications of shift registers are

Time delay
Ring counter
Serial to parallel data conversion
Serial to serial data conversion

Which of the above are correct?
1, 2, 3
2, 3, 4
1, 2, 3, 4
1, 2, 4

⇒ RMS value of i(t) = 10[1 + sin (- t)] is
10
10/2
l50
102

⇒ Waves of frequencies higher than 30 MHz penetrate the atmosphere.
TRUE
FALSE

⇒ Which of the following is used for generating time varying wave forms?
MOSFET
PIN diode
Tunnel diode
UJT

⇒

Assertion (A): L[e^-at f(t)] = F(s + a)

Reason (R): In use of Laplace transform method, initial conditions may be neglected.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ Voltage 1 + 2 sin ωt is applied to the circuit shown be
0 volt
2 volts
-2 volts
-3 volts

⇒ Electric lines of force do not cross each other because
the lines of force mutually repel each other
the lines of force emanate from a point charge
the tangent to the line of force gives the direction of E and if they cross two tangents for E which is not possible
none of the above

⇒ The figure shown below is designed to act as a constant current source across the load resistor. The β of transistor is 50. What is the value of load curr
1.96 mA
2 mA
2.04 mA
None

⇒ The autocorrelation function of the white noise is
impulse function
step function
constant
none of the above

⇒ Loading effect is primarily caused by instruments having
high resistance
high sensitivity
low sensitivity
high range

⇒

Assertion (A): In standing wave pattern, the nodes and anti nodes are separated by half wave-length

Reason (R): When line is terminated in resistance R_L, the standing wave ratio is SWR = Z₀/R_L or R_L/Z₀

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ The time constant of the network shown in figur
2 RC
5/3 RC
RC/2
None of these

⇒ For the characteristic equation s⁵ + s⁴ + 2s³ + 2s² + 3s + 15 = 0, the number of roots in left half s plane are
1
2
3
5