Question is ⇒ Which is the displacement transducer with excellent sensitivity, linearity and resolution?, Options are ⇒ (A) Incremental encoder, (B) Absolute encoder, (C) LVDT, (D) Strain gauge, (E) , Leave your comments or Download question paper.

Question is ⇒ Which is the displacement transducer with excellent sensitivity, linearity and resolution?, Options are ⇒ (A) Incremental encoder, (B) Absolute encoder, (C) LVDT, (D) Strain gauge, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Which is the displacement transducer with excellent sensitivity, linearity and resolution?
A.	Incremental encoder [Wrong Answer]
B.	Absolute encoder [Wrong Answer]
C.	LVDT [Correct Answer]
D.	Strain gauge [Wrong Answer]
View Answer 3 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒

Assertion (A): When a high reverse voltage is applied to a p-n junction the diode breaks down.

Reason (R): High reverse voltage causes Avalanche effect.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ Microwave links are typically 50 km apart
because of atmospheric attenuation
because of output tube power limitation
because of earth's curvature
to ensure that applied dc voltage is not excessive

⇒ In a TWT the amplitude of resultant wave travelling down the helix
increases exponentially
increases linearly
decreases exponentially
is almost constant

⇒ Which of the following modes of transmission will not be supported by a rectangular waveguide?
TE₁₅
TE₁₂
TM₁₁
TM₁₀

⇒ In 8085
RST 6.5 and RST 5.5 are high level sensitive interrupts
RST 6.5 and RST 5.5 are low level sensitive interrupts
RST 5.5 is low level sensitive interrupt but RST 5.5 is high level-sensitive interrupt
RST 5.5 is low level sensitive interrupt but RST 6.5 is high level sensitive interrupt

⇒ High frequency waves are
absorbed by F₂ layer
affected by solar cycle
reflected by D layer
none of the above

⇒ Soft iron is suitable for making temporary magnets.
TRUE
FALSE

⇒ A binary adder has
one half adder
one half adder and 2 full adders
two half adders
one half adder and many full adders

⇒ In PCM, the quantization noise depends on
sampling rate
signal power
number of quantization level
signal energy

⇒ Which of the following best represents the output impedance of an actual op-amp?
10 ohm
100 ohm
10 k ohm
100 k ohm

⇒ Which of the following conditions must be satisfied for a transistor to remain under saturation?

Its collector to base junction should be under forward bias.
Its collector to base junction should be under reverse bias.
Its emitter to base junction should be under reverse bias.
Its emitter to base junction should be under forward bias.

Select the correct answer from the codes given below:
1 and 2
1 and 3
2 and 3
1 and 4

⇒

Assertion (A): Typical value of thermal resistance from source to sink of an SCR is about 0.3° C/W

Reason (R): Heat sinks of thyristors are generally made of aluminium.

Both A and R are correct and R is correct explanation of A
Both A and R correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ Consider the following statements about Java variables

Java variable must start with a letter or underscore or dollor sign.
Java variable can not start with a digit.
After the first character the variable can have any combination of letters or numbers.
Capitalization of letters must be consistent.

Which of the above are correct?
All
1, 2 and 3 only
2, 3, 4 only
1, 2 and 4 only

⇒ Power spectral density of white noise
is constant with frequency
increases with frequency
decreases with frequency
none

⇒ If two networks are connected in series of individual Z parameter as Z_a and Z_b then equivalent Z is
[Z] = [Z_a] + [Z_b]
[Z] = [Z_a] [Z_b]
[Z] = [Z_a]/[Z_b]
[Z] = [Z_a] - [Z_b]

⇒ In a TV receiver the raster is normal but there is no sound and quality of picture is poor. The defective part is
power supply
loudspeaker
AGC, video IF amplifier, RF amplifier
horizontal oscillator

⇒

Assertion (A): Hall effect is observed in all metals but is very appreciable in semiconductors.

Reason (R): Hall effect transducer is very suitable for measurement of magnetic flux density.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒ Which of the following may result in instability problem?
Large error
High selectivity
High gain
Noise

⇒ The residual resistivity of a binary alloy at 0°K is
the sum of the residual resistivities of the component metals
the difference of the residual resistivities of the component metals
the product of the residual resistivities of the component metals
depend on the concentration of the minor component in the alloy

⇒ PA radar means
Phased Array radar
Pulsed Array radar
Pulse Amplitude radar
None of the above

⇒ The number of spectral component when two sine wave of same frequency multiplied is
2
3
∞
4

⇒ Rank of the matr
3
2
1
4

⇒ Figure shows an RC circuit. The magnitude plot V₂/V_{1will rise exponentially to R₂/(R₁ + R₂) as ω → ∞
will rise linearly to R₂/(R₁ + R₂) as ω → ∞
will decrease to zero as ω → ∞
will rise 1 at ω = 0 and then decrease as ω → ∞}

⇒ Figure shows the arrangement
FM
PM
AM-DSB
AM-SSB

⇒ A rectangular metal waveguide filled with a dielectric of relative permittivity ε_r = 4, has the inside dimensions 3 x 1.2 cm, the cut off frequency for the dominant mode is
2.5 GHz
5 GHz
10 GHz
12.5 GHz

⇒ In a thyristor, the forward breakover voltage
is constant
may be constant or may depend on gate current
decreases as gate current is increased
increases as gate current is increased

⇒

Assertion (A): In direct addressing the address of operand is specified in the instruction.

Reason (R): Direct addressing is also called absolute addressing.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ In figure, V_{0zero
5.7 V
6.9 V
12.6 V}

⇒ The advantages of flash memory over EEPROM are
higher density
lower cost
both higher density and lower cost
none of the above

⇒ An electron in the conduction band
has higher energy than the electron in the valence band
has lower energy than the electron in the valence band
loses its charge easily
jumps to the top of the crystal