Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | Which has the highest power dissipation per gate? |

A. | ECL [Correct Answer] |

B. | TTL [Wrong Answer] |

C. | CMOS [Wrong Answer] |

D. | PMOS [Wrong Answer] |

View Answer
Explanation:-
Answer : ADiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ If the target cross-section is changing, the best scanning system for accurate tracking is

lobe switching

monopulse

sequential lobing

conical scanning

⇒ A parallel in-parallel out shift register can be used to introduce delay in digital circuits.

TRUE

FALSE

⇒ The output V-I characteristics of an Enhancement type MOSFET has

only an ohmic region

only a saturation region

an ohmic region at low voltage value followed by a saturation region at higher voltages.

an ohmic region at large voltage values. Preceded by a saturation region at lower voltages.

⇒ Which of the following is a valid real constant?

-81.56

73

10254,1

42

⇒ The most suitable method for detecting a modulated signal

*g*(

*t*) = (3 to 6 cos 2p

*f*) cos 2p

_{m}t*f*is

_{c}tenvelope detector

synchronous detector

ratio detector

both a and b

⇒ In low power factor wattmeter, the pressure coil is connected

to the supply side of current coil

to the load side of current coil

in either (a) or (b)

across the mains

⇒ In the graph of figure, the total number of tree

4

5

6

8

⇒ A linear displacement digital transducer generally uses

straight binary code

BCD

gray code

hexadecimal code

⇒ The carriers of

*n*channel JFET are

free electrons and holes

holes

free electrons or holes

free electrons

⇒ The signumm function written as [

*sgn(*] is defined as

*t*)*sgn(t)*= - 1 for

*t*< 0, = 0 for

*t*= 0 and = 1 for

*t*> 0

*sgn(t)*= 1 for

*t*< 0, = 0 for

*t*= 0 and = - 1 for

*t*> 0

*sgn(t)*= 0 for

*t*< 0, = 1 for

*t*= 0 and = 0 for

*t*> 0

*sgn(t)*= 0 for

*t*< 0, = 1 for

*t*

^{3}0

⇒ In the given figure shows a negative logic AND gate. If positive logic is used this gate is equivalen

AND gate

OR gate

NOR gate

NAND gate

⇒ In drawing phasor diagrams, RMS values are used.

TRUE

FALSE

⇒ Measurement of an unknown voltage with a dc potentiometer loses its advantage of open circuit measurement when

the primary circuit battery is changed

standardization has to be done again to compensate for drifts

voltage is larger than range of the potentiometer

range reduction by a factor of 10 is employed

⇒ In force voltage analogy, displacement is analogous to

current

voltage

charge

none of the above

⇒ In a colour TV receiver, AGC adjusts the gain of

RF stage only

IF stage only

RF stage and one or two IF stages

none of the above

⇒ The total number of fundamental products of three variables is

3

5

8

16

⇒ V-I relationship of a network N is given by, V = 8 -

0, 2

0, 4

2, 4

None of these

⇒ The simplest standing wave is due to the value of reflection co-efficient is

-1

zero

unity

infinity

⇒ Inverse Fourier transform of '1' is

U(

*t*)

δ(

*t*)

0'

infinite

⇒ The

*Z*inverse of the given

*Z*transform i

unit step

unit impulse

unit ramp

unit parabola

⇒ In an LC immittance H (

*s*)

the slope of

*d*H (

*j*ω)/

*d*ω is always negative

the slope of

*d*H (

*j*ω)/

*d*ω is always positive

the slope of

*d*H (

*j*ω)/

*d*ω may be positive or negative

the slope of

*d*H (

*j*ω)/

*d*ω is constant

⇒ For a single phase half wave converter feeding a resistive load, the firing angle a. The waveshape in below figure is

output voltage

input voltage

voltage drop across thyristor

none of the above

⇒ In figure, the current through

*R*is 1 A when V

_{A}= 0 and V

_{B}= 15V. If both V

_{A}and V

_{B}are increased by 15V each, current through R wil

0.0416666666666667

0.5 A

0.125

0.33 A

⇒ A linear time-invariant, causal continuous time system has a rational transfer function with simple poles at

*s*= - 2 and

*s*= - 4, and one simple zero at

*s*= - 1. A unit step

*u*(

*t*) is applied at the input of the system. At steady state, the output has constant value of 1. The impulse response of this system is

[exp (- 2

*t*) + exp (-4

*t*)]

*u*(

*t*)

[-4 exp (- 2

*t*) + 12 exp (-4

*t*) - exp (-

*t*)]

*u*(

*t*)

[-4 exp (- 2

*t*) + 12 exp (-4

*t*)]

*u*(

*t*)

[-0.5 exp (- 2

*t*) + 1.5 exp (-4

*t*)]

*u*(

*t*)

⇒ For the NMOS gate in the given figure,

ABCDE

(AB + C) (D + E)

A(B + C) + DE

A + B C + DE

⇒ The distributors for residential areas are

single phase

three phase three wire

three phase 4 wire

(a) or (b)

⇒ Cells are connected in series to increase

current-rating

both voltage and current rating

the life of cell

voltage rating

⇒ Which of the following is not an assembler directive in 8085?

D S

D B

D Q

E Q U

⇒ In an

*n*channel MOSFET, the substrate is connected

to negative terminal of battery

to positive terminal of battery

to either positive or negative terminal of battery

none of the above

⇒ Find R

_{TH}across the terminals A a

52.28 Ω

58.28 Ω

52.82 Ω

58.82 Ω