Question is ⇒ When two D.C. series motors are connected in parallel, the resultant speed is, Options are ⇒ (A) more than the normal speed, (B) loss than the normal speed, (C) normal speed, (D) zero, (E) , Leave your comments or Download question paper.

Question is ⇒ When two D.C. series motors are connected in parallel, the resultant speed is, Options are ⇒ (A) more than the normal speed, (B) loss than the normal speed, (C) normal speed, (D) zero, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	When two D.C. series motors are connected in parallel, the resultant speed is
A.	more than the normal speed [Wrong Answer]
B.	loss than the normal speed [Wrong Answer]
C.	normal speed [Correct Answer]
D.	zero [Wrong Answer]
View Answer 4 -39 Explanation:- Answer : C Discuss it below : S RAVI Said on 2019-05-15 02:40:01 When two DC series motor are connected in parallel then the resultant speed is increase the normal speed. If the voltage across each motor is assumed to be V, then current through each motor in parallel connection will be I/2. So, speed α (voltage/current) α (V/Ia/2). Hence the resultant speed is more than normal speed. !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ For constant torque drive which speed control method is preferred ?
Field control
Armature voltage control
Shunt armature control
Mechanical loading system

⇒ The speed of a D.C. shunt motor can be increased by
increasing the resistance in armature circuit
increasing the resistance in field circuit
reducing the resistance in the field circuit
reducing the resistance in the armature circuit

⇒ The losses occurring in a D.C. generator are given below. Which loss is likely to have the least proportion ?
Magnetic losses
Armature copper losses
Mechanical losses
Field copper losses

⇒ For a D.C. shunt motor if the excitation is changed
torque will remain constant
torque will change but power will remain constant
torque and power both will change
torque, power and speed, all will change

⇒ Which loss in a D.C. generator varies with load ?
Copper loss
Eddy current loss
Hysteresis loss
Windage loss

⇒ If the field of a D.C. shunt motor gets opened while motor is running
the speed of motor will be reduced
the armature current will reduce
the motor will attain dangerously high speed
the motor will continue to run at constant speed

⇒ If B_max is the maximum flux density, then eddy cu rrent loss will vary as
B_max
(B_max)²
(B_max)^1.2
(B_max)^2.4

⇒ A three point starter is considered suitable for
shunt motors
shunt as well as compound motors
shunt, compound and series motors
all D.C. motors

⇒ In which of the following applications D.C. series motor is invariably tried?
Starter for a car
Drive for a water pump
Fan motor
Motor operation in A.C. or D.C.

⇒ For which application a D.C. motor is preferred over an A.C. motor ?
High speed operation
Low speed operation
Fixed speed operation
Variable speed operation

⇒ If a D.C. shunt motor is working at no load and if shunt field circuit suddenly opens
nothing will happen to the motor
this will make armature to take heavy current, possibly burning it
this will result in excessive speed, possibly destroying armature due to excessive centrifugal stresses
motor will run at very slow speed

⇒ Which motor should be used for centrifugal pumps ?
Series motor
Shunt motor
Either of the above
None of the above

⇒ Which of the following motor has the poorest speed regulation ?
Shunt motor
Series motor
Differential compound motor
Cumulative compound motor

⇒ A 230 V D.C. shlint motor takes 32 A at full load. The back e.m.f. on full load, if the resistance of motor armature and shunt field windings are 0.2 Ω and 115 Ω respectively, will be
210 V
215 V
220 V
224 V

⇒ The mechanical power developed by a D.C. motor is equal to
power input + losses
back e.m.f. X armature current
power output X losses
power output X efficiency

⇒ Three point starter can be used for
series motor only
shunt motor only
compound motor only
both shunt and compound motor

⇒ The function of a field regulator for compound motors is to
control the flux
limit the armature current
demagnetise the field partially
none of the above

⇒ Which D.C. motor is preferred for elevators ?
Shunt motor
Series motor
Differential compoun.d motor
Cumulative compound motor

⇒ Speed control by the variation of flux, in a D.C. shunt motor, will give
constant torque drive
variable torque drive
constant power drive
variable power drive

⇒ The power mentioned on the name plate of an electric motor indicates
the power drawn in kW
the power drawn in kVA
the gross power
the output power available at the shaft

⇒ At the instant of starting when a D.C. motor is put on supply, it behaves like
a highly resistive circuit
a low resistance circuit
a capacitive circuit
none of the above

⇒ Which of the following loss in a D.C. generator varies significantly with the load current ?
Field copper loss
Windage loss
Armature copper loss
None of the above

⇒ The total losses in a well designed D.C. generator of 10 kW will be nearly
100 W
500 W
1000 W
1500 W

⇒ No-load speed of which of the following motor will be highest ?
Shunt motor
Series motor
Cumulative compound motor
Differentiate compound motor

⇒ The losses occurring in a D.C. generator are given below. Which loss is likely to have highest proportion at rated load of the generator ?
hysteresis loss
field copper loss
armature copper loss
eddy current loss

⇒ In D.C. shunt motors as load is reduced
the speed will increase abruptly
the speed will increase in proportion to reduction in load
the speed will remain almost constant
the speed will reduce

⇒ A wide and very sensitive speed control is usually required in case of
elevators
steel rolling mills
colliery winders
all of the above

⇒ Which D.C. motor will be suitable alongwith flywheel for intermittent light and heavy loads?
Series motor
Shunt motor
Cumulatively compounded motor
Differentially compounded motor

⇒ In Ward Leonard method of speed control of a D.C. motor, change in speed of motor is obtained by the
change in armature voltage of D.C. motor
change in the field excitation of the D.C. motor
change in armature current of D.C. motor
change in supply voltage

⇒ Which of the following methods gives the greatest breaking torque ?
Regenerative braking
Plugging
Rheostatic braking
None of the above.