Question is ⇒ When the interconnector between two stations has large reactance, Options are ⇒ (A) the transfer of power will take place with voltage fluctuation and noise, (B) the transfer of power will take place with least loss, (C) the stations will fall out of step because oflarge angular displacement, between the stations, (D) none of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ When the interconnector between two stations has large reactance, Options are ⇒ (A) the transfer of power will take place with voltage fluctuation and noise, (B) the transfer of power will take place with least loss, (C) the stations will fall out of step because oflarge angular displacement, between the stations, (D) none of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	When the interconnector between two stations has large reactance
A.	the transfer of power will take place with voltage fluctuation and noise [Wrong Answer]
B.	the transfer of power will take place with least loss [Wrong Answer]
C.	the stations will fall out of step because oflarge angular displacement, between the stations [Correct Answer]
D.	none of the above [Wrong Answer]
View Answer 9 -3 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which of the following characteristics should the line supports for transmission lines possess ?
Low cost
High mechanical strength
Longer life
All of the above

⇒ The operating voltage of supertension cables is upto
3.3 kV
6.6 kV
11 kV
33 kV

⇒ Which of the following bus-bar schemes has the lowest cost ?
Ring bus-bar scheme
Single bus-bar scheme
Breaker and a half scheme
Main and transfer scheme

⇒ For an overhead line, the surge impedance is taken as
20-40 ohms
70-80 ohms
100-200 ohms
500-1000 ohms

⇒ Which of the following materials is not used for transmission and distribution of electrical power ?
Copper
Aluminium
Steel
Tungsten

⇒ In which of the following voltage regulators the effect of dead zero is found ?
Electromagnetic type
Magnetic amplifier
Electronic type using integrated circuits
All of the above

⇒ Which of the following are connected by the service mains ?
Transformer and earth
Distributor and relay system
Distributor and consumer terminals
Distributor and transformer

⇒ For aluminium, as compared to copper, all the following factors have higher values except
specific volume
electrical conductivity
co-efficient of linear expansion
resistance per unit length for same cross-section

⇒ The voltage regulation in magnetic amplifier type voltage regulator is effected by
electromagnetic induction
varying the resistance
varying the reactance
variable transformer

⇒ Besides a method of trial and error, which of the following methods is employed for solution o f network problems in interconnected system ?
Circulating current method
Thevenin's theorem
Superposition of currents
Direct application of Kirchhoff's laws

⇒ If the voltage is increased x times, the size of the conductor would be
reduced to 1/x² times
reduced to 1/x times
increased x times
increased to x² times

⇒ The operating voltage of extra high tension cables is upto
66 kV
11 kV
33 kV
66 kV

⇒ The cause of damage to the lead sheath of a cable is
crystallisation of the lead through vibration
chemical action on the lead when buried in the earth
mechanical damage
all of the above

⇒ ____ are the conductors, which connect the consumer's terminals to the distribution
Distributors
Service mains
Feeders
None of the above

⇒ In the design of a distributor which of the following is the major consideration ?
Voltage drop
Current carrying capacity
Frequency
kVA of system

⇒ When the load at the receiving end of a long transmission line is removed, the sending end voltage is less than the receiving end voltage. This effect is known as
Ferranti effect
Proximity effect
Kelvin effect
Faraday effect

⇒ Overhead system can be designed for operation upto
11 kV
33 kV
66 kV
400 kV

⇒ The steel used in steel cored conductors is usually
alloy steel
stainless steel
mild steel
high speed steel

⇒ Out of the following which type of poles are bulky ?
Transmission towers
Concrete poles
Tubular steel poles
Wooden poles

⇒ In the analysis of which of the following lines shunt capacitance is neglected ?
Short transmission lines
Medium transmission lines
Long transmission lines
Medium as well as long transmission lines

⇒ In aluminium conductors, steel core is provided to
compensate for skin effect
neutralise proximity effect
reduce line inductance
increase the tensile strength

⇒ In transmission lines the cross-arms are made of
copper
wood
R.C.C.
steel

⇒ Galvanised steel wire is generally used as
stay wire
earth wire
structural components
all of the above

⇒ Which of the following is the demerit of a 'constant voltage transmission system' ?
Increase of short-circuit, current of the system
Availability of steady voltage at all loads at the line terminals
Possibility of better protection for the line due to possible use of higher terminal reactances
Improvement of power factor at times of moderate and heavy loads

⇒ When the interconnector between two stations has large reactance
the transfer of power will take place with voltage fluctuation and noise
the transfer of power will take place with least loss
the stations will fall out of step because oflarge angular displacement, between the stations
none of the above

⇒ The conductors of the overhead lines are
solid
stranded
both solid and stranded
none of the above

⇒ Which of the following D.C. distribution system is the simplest and lowest in first cost, ?
Radial system
Ring system
Inter-connected system
None of the above

⇒ Power system stability is least affected by
reactance of generator
input torque
losses
reactance of transmission line

⇒ For transmission of power over a distance of 500 km, the transmission voltage should be in the range
150 to 220 kV
100 to 120 kV
60 to 100 kV
20 to 50 kV

⇒ A booser is connected in
parallel with earth connection
parallel with the feeder
series with the feeder
series with earth connection