Question is ⇒ When a thyristor is conducting, the voltage drop across it, Options are ⇒ (A) is absolutely constant, (B) decreases with increase in load current, (C) increases slightly with increase in load current, (D) none of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ When a thyristor is conducting, the voltage drop across it, Options are ⇒ (A) is absolutely constant, (B) decreases with increase in load current, (C) increases slightly with increase in load current, (D) none of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	When a thyristor is conducting, the voltage drop across it
A.	is absolutely constant [Wrong Answer]
B.	decreases with increase in load current [Wrong Answer]
C.	increases slightly with increase in load current [Correct Answer]
D.	none of the above [Wrong Answer]
View Answer 4 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The value of capacitor C for dynamic equalising circuit of series connected thyristors is determined by
forward characteristics of thyristors
reverse recovery characteristics of thyristors
both forward and reverse recovery characteristics of thyristors
none of the above

⇒ What is the normal range of analog input voltage?
0 to 1 V
0 to 5 V
5 to 15 V
15V to 30V

⇒ Fastest memory cell
bubble memory
core memory
semiconductor memory
superconductor memory

⇒ In a Vidicon camera tube
grid G₁ accelerates electrons
grid G₂ accelerates electrons and grid G₃, slows down electrons
grid G₃ accelerates electrons and grid G₂ slows down electrons
both grids G₂ and G₃ accelerate electrons

⇒ In telephone systems, load is expressed in the unit of
erlangs
decibels
bells
watts

⇒ Three phase four wire induction energy meter is used to measure
energy in 3 phase balanced star load
energy in 3 phase balanced delta load
energy in 3 phase unbalanced load
either (a) or (b)

⇒ An m derived and constant k filter section connected in cascade give
proper impedance matching
proper phase shift characteristic
proper attenuation characteristic
all of the above

⇒ The circuit shown in the figure has 4 boxes each described by inputs P, Q, R and outputs Y, Z
4 bit adder giving P + Q
4 bit subtractor giving P - Q
4 bit subtractor giving Q - P
4 bit adder giving P + Q + R

⇒ The resistance of resistance strain gauge is about
5 Ω
50 Ω
120 Ω
0.5 Ω

⇒ A constant k high pass p section has a characteristic impedance of 300 Ω at f = ∞ . At f = f_c, the characteristic impedance will be
zero
∞
300 Ω
more than 300 Ω

⇒ Crossover distortion behaviour is characteristic of
class A O/P stage
class B O/P stage
class AB output stage
common pulse O/P state

⇒ The frequency tolerance for the RF carrier in the standard AM radio broadcast band is
zero
+20 Hz
+1000 Hz
+25 Hz

⇒ Volume control found on the front panel of television receivers
a ganged resistor
a variable resistor of logarithmic type
a variable resistor of linear type
a trimmer potentiometer

⇒ Point out the false statement
impulse noise voltage does not depend on bandwidth
thermal noise is independent of frequency at which it is measured
industrial noise is mostly of impulse type
space noise is observable at frequencies in the range of 8 MHz and higher

⇒ An ac wave with superimposed dc is symmetrical about x - axis.
TRUE
FALSE

⇒ The following table gives some time functions and the Laplace transf
2 and 4
1 and 4
3 and 4
1 and 2

⇒ Binary number 1101.101 is equivalent to decimal number?
13.5
13.75
13.625
13.875

⇒ For the current wave i = 10 + 10 sin θ, the rms value is
0.416666666666667
12.247 A
20 A
14.14 A

⇒ The conductivity of intrinsic semiconductor is given by
en_i(μ_p - μ_n)
en_i(μ_p + μ_n)
n_i(μ_p + μ_n)
n_i(μ_pμ_n)

⇒ Dielectric constant of transformer oil is about
1
4
10
20

⇒ Two sinusoidal voltage sources v₁ = 50 sin (100t) and v₁ = 50 sin (100t + p) are connected in parallel and fed an inductance X_L = 2Ω. The cuirent through X_L is
25 A
about 17.5 A
zero
50 A

⇒ A TRIAC is equivalent to
two thyristors in series
two thyristors in parallel
one thyristor and one diode
one thyristor and one transistor

⇒ When a plane wave is incident normally from dielectric '1' (μ₀, ε₁) onto dielectric '2' (μ₀, ε₂) the electric field of the transmitted wave is 2 times the electric field of the reflected wave. The ratio ε₂/ε₁ is
0.5
1
2
4

⇒ Bridge circuits using RTD in temperature measurement usually employ 3 lead system so as to obtain
higher sensitivity
better impedance matching
compensation for signal wire resistance
reduction in power consumption

⇒ The signal input to a given amplifier is made up of 100 mΩ signal power and 1 mΩ noise power. The amplifier contributes an additional 100 mΩ of noise and has a power gain of 20 dB. The noise factor is
1
1.5
2
15

⇒ Circular polarized waves result when
magnitudes are the same
phases are the same
magnitudes are same and phase difference is 90°
magnitudes are same and phase difference is zero

⇒ I-PD controlled system has
I, P and D actions in forward path
I, P and D actions in feedback path
I action in forward path but P and D action in feedback path
I action in feedback path but P and D actioins in forward path

⇒ Consider the following program for 8085 decimal 20
decimal 40
decimal 10
none of the above

⇒ In a specimen of n type semiconductor, the initial concentration of holes and electrons is p_no and n_no. When the specimen is subjected to radiation, the hole and electron concentration increase to p_n and n_n. Then
p_n - p_no = n_n - n_no
p_n + p_no = n_n + n_no
p_n - p_no = n_no + n_no
p_n + p_no = n_n - p_no

⇒

Assertion (A): The line integral of B about a closed contour, in a region containing steady current, is μ₀ times the total net current, following through the contour of integration.

Reason (R): The curl of B is equal to μ₀ times the current density vector J

Both (A) and (R) are true and (R) is the correct explanation of (A)
Both (A) and (R) are true but (R) is not the correct explanation of (A)
(A) is true but (R) is false
(A) is false but (R) is true