Question is ⇒ When a single phase dual converter is operating in circulating current mode, Options are ⇒ (A) both converters are working as rectifiers simultaneously, (B) one converter is always working as rectifier and the other as inverter, (C) only one converter is working at one time, (D) both converters are either working as rectifiers or as inverters simultaneously, (E) , Leave your comments or Download question paper.

Question is ⇒ When a single phase dual converter is operating in circulating current mode, Options are ⇒ (A) both converters are working as rectifiers simultaneously, (B) one converter is always working as rectifier and the other as inverter, (C) only one converter is working at one time, (D) both converters are either working as rectifiers or as inverters simultaneously, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	When a single phase dual converter is operating in circulating current mode
A.	both converters are working as rectifiers simultaneously [Wrong Answer]
B.	one converter is always working as rectifier and the other as inverter [Correct Answer]
C.	only one converter is working at one time [Wrong Answer]
D.	both converters are either working as rectifiers or as inverters simultaneously [Wrong Answer]
View Answer 1 -2 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Some typical examples of macroscopic quantities are
conductivity
µ_r
dielectric constant
all of the above

⇒ The dual of quantity charge is
current
Voltage
flux
dΦ/dt

⇒ Quality factor will be
a/b
b/a
b/a
ab

⇒ How many JK flip-flops are needed to make a 4-bit shift register?
2
4
6
8

⇒ Fill in the suitable word in the blanks is the following questions. The electron in the outermost orbit is called __________ electron.
valence
covalent
acceptor
donor

⇒ Two sinusoidal waves 1 and 2 have peak values V_m1 and V_m2. Wave 1 is leading wave 2 by ∠θ. Which of the following is correct?
v₁ = V_m1 sin θ and v₂ = V_m2 cos θ
v₁ = V_m1 sin ωt and v₂ = V_m2 sin (ωt - θ)
v₁ = V_m1 sin (ωt + θ/2) and v₂ = V_m2 sin ωt
none of the above

⇒ An 8 level encoding scheme is used in a PCM system of 10 kHz channel BW. The channel capacity is
80 kbps
60 kbps
30 kbps
18 kbps

⇒ The ripple factor of a full wave rectifier is about 0.5.
TRUE
FALSE

⇒ If H(s) is positive real, 1/H(s)
is positive real
is not positive real
may or may not be positive real
must possess some other properties also if it is to be positive real

⇒ Stepper motors find applications in
X-Y plotters
numerically controlled machining equipment
printers
all of the above

⇒ Find the electric charge required on the earth and moon to balance their gravitational attraction if the charge on the earth is 12.5 times that on the m
48.9 TC
4.89 GC
4.89 TC
48.9 GC

⇒ The essential condition for antenna array to be linear is that
individual antennas of the array must be of equal size
individual antennas of the array must be equally spaced along a straight line
any two individual antennas of the array must not be in the same direction
none of the above

⇒

Assertion (A): Positive feedback is not used in any circuit.

Reason (R): Positive feedback leads to instability.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒ If V_in is 0.99 V, what is the digital output of the ADC 0801 after INTER goes low?
0011 0011
0101 1111
0111 1100
1111 1111

⇒ In MF range, increasing the transmitter power
increases the range of transmitter
does not increase the range of transmitter because propagation is limited by tilt
decreases the range of transmitter because propagation is limited by tilt
increases the range of transmitter because propagation is through space waves

⇒

Assertion (A): A dual converter may be circulating current type or non circulating current type.

Reason (R): In circulating current dual converter only one converter can be operated at one time.

Both A and R are correct and R is correct explanation of A
Both A and R correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ The given figure shows a constant current source driving a parallel RC circuit. It is equivalen
a lag network
a lead network
a lag-lead network
either (a) or (b)

⇒ It is desired to clean up ragged looking pulsed that have been distorted during transmission from one place to another, which of the following device will be appropriate?
Multiplexer
D/A converter
JK flip-flop
Schmitt trigger

⇒ Twelve resistance each 2 ohm are connected to form a cube, one resistance being in each arm of cube. The resistance between any two diagonally opposite comers is
1 Ω
2 Ω
4 Ω
8 Ω

⇒ The mean life time of the minority carriers is in the range of a few
seconds
milli seconds
micro seconds
nano seconds

⇒ At night D layer of ionosphere is absent.
TRUE
FALSE

⇒ The advantage of FET over BJT is
high input impedance
lower noise
no thermal runaway
all of the above

⇒ A function table is required in very large numbers the memory most switched for this purpose would be
ROM
PROM
EPROM
EAROM

⇒ The relation between plate current and plate voltage of a vacuum diode is called
Richardson Dushman equation
Langmuir Child law
Ohm's law
Boltzmann's law

⇒ Which of the following is not a wideband antenna?
Marconi
Discone
Helical
Folded dipole

⇒ An open loop system has a forward path transfer function (42.25)/s(s + 6.5). The unit step response of the system starting from rest will have its maximum value at a time equal to
0 sec
0.56 sec
5.6 sec
infinity

⇒ The bidirectional pattern of a broadside array can be converted into unidirectional by
maintaining the distance of λ/4 between the elements
maintaining the distance of λ/2 between the elements
installing an identical array behind the main array at distance λ/4 and exciting it by current leading in phase by 90°
installing an identical array behind the main array at distance λ/2 and exciting it by current leading in phase by 120°

⇒ Consider the following statements about 'Functions' in C

A function can be called any number of times.
A function gets called when the function name is followed by a semicolon.
The order in which functions are defined in a program and the order in which they are called must be the same.

Which of the above statements are correct?
All
1 and 2 only
1 and 3 only
2 and 3 only

⇒ Consider the following statements about root locus

The intersection of root locus branches with the imaginary axis can be determined by the use of Routh criterion
Segments of real axis having an odd number of real axis open loop poles plus zeros to their right are not parts of root locus
The number of root locus branches terminating on infinity is always zero

Which of the above statements are correct?
1, 2 and 3
1 and 2 only
1 only
2 and 3 only

⇒ The value of VSWR is taken as ∞ when the line is
short-circuited
open-circuited
terminated with full load
terminated with load equal to the characteristic impedance of the load