Question is ⇒ When a diode is not conducting, its bias is, Options are ⇒ (A) forward, (B) zero, (C) reverse, (D) zero or reverse, (E) , Leave your comments or Download question paper.

Question is ⇒ When a diode is not conducting, its bias is, Options are ⇒ (A) forward, (B) zero, (C) reverse, (D) zero or reverse, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	When a diode is not conducting, its bias is
A.	forward [Wrong Answer]
B.	zero [Wrong Answer]
C.	reverse [Wrong Answer]
D.	zero or reverse [Correct Answer]
View Answer 1 -1 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The concentration of minority carriers in an extrinsic semiconductor under equilibrium is
directly proportional to the doping concentration
inversely proportional to doping concentration
directly proportional to intrinsic concentration
inversely proportional to the intrinsic concentration

⇒ A piezoelectric force transducer has a charge sensitivity of 20 pC/N. It is connected to a charge amplifier and overall gain of transducer and amplifier is 50 mV/N. The gain of amplifier is
1 mV/pC
1.5 mV/pC
2.5 mV/pC
4 mV/pC

⇒ In MF range, increasing the transmitter power
increases the range of transmitter
does not increase the range of transmitter because propagation is limited by tilt
decreases the range of transmitter because propagation is limited by tilt
increases the range of transmitter because propagation is through space waves

⇒ For the system in the given figure. The transfer function C(s)/R(s
G₁ + G₂ + 1
G₁ G₂ + 1
G₁ G₂ + G₂ + 1
G₁ G₂ + G₁ + 1

⇒ A dc circuit breaker must use
natural commutation
forced commutation
both natural and forced commutation
either natural or forced commutation

⇒ Dynamic memory cells are constructed using
FETs
MOSFETs
Transistors
Flip flops

⇒ The logic operation that will selectively clear bits in register A in those positions where these are 1 's in the bits of register B is given by
A ← A + B
A ← AB
A ← A + B
A ← AB

⇒ In FM modulation pre-emphasis is done for
high frequency components
low frequency components
middle frequency components
both (a) and (b)

⇒ When signed numbers are used in binary arithmetic, which of the following has unique representation for zero?
Sign-magnitude
1's complement
2's complement
9's complement

⇒ Choose the correct option, if b (branch), n (nodes), l (links)
b = n + l - 1
no. of twig = n - 1
b = n - l + 1
b, a

⇒ A radiation thermometer is suitable for temperatures
below 500°C
below 100°C
above 500°C
above 1400°C

⇒ Transformer oil is
refined vegetable oil
refined mineral oil
mixture of vegetable and mineral oil
none of the above

⇒ Which of the following is not a classification of programmed data transfer?
Synchronous transfer
Hand shaking
Interrupt driver transfer
Direct transfer

⇒ What is the addressing mode used in instruction MOV M, C?
Direct
Indirect
Induced
Immediate

⇒ If x^k is one sided to the ri
TRUE
FALSE

⇒ No load d.c. output will be least in case of
half wave rectifier
full wave rectifier
bridge rectifier
three phase full wave rectifier

⇒ The frequency deviation of a FM signal produced from PM is
identical to that of FM signal produced by direct method
larger than that of a FM signal produced by direct method
directly proportional to the peak amplitude and the frequency of modulating signal
directly proportional to the peak amplitude of the modulating signal

⇒

Assertion (A): The variable name 5KING is not valid in Fortran 77.

Reason (R): In Fortran 77 the first character of a variable name must be an alphabet.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ The sensitivity of a voltmeter using 0-5 mA meter movement is
50 Ω/V
100 Ω/V
200 Ω/V
500 Ω/V

⇒ Calculate the directivity of an antenna for θ_E = 30°, θ_H = 60
46
23
50
100

⇒ A two stage amplifier has an upper cutoff frequency of 2 MHz and a lower cutoff frequency of 2 MHz and a lower cut off frequency of 30 Hz. If both stages are similar, their individual upper and lower cut off frequencies respectively are
4 MHz and 60 MHz
3 MHz and 20 Hz
3 MHz and 60 Hz
4 MHz and 20 Hz

⇒ A signal m(t) = 5 cos 2p 100 t frequency modulates a carrier. The resulting FM signal
0.1 kHz
6 kHz
3.2 kHz
100 kHz

⇒ In PCM, the biggest disadvantage as compared to AM is
larger bandwidth
larger noise
inability to handle analog signals
incompatibility with time division multiplex systems

⇒ With JFETs cascade means
a common source driving a common gate connection
a common gate driving a common source connection
two FETs connected in parallel
none of the above

⇒ To neglect a current source the terminals across the source are
replaced by some resistance
replaced by capacitance
open-circuited
short-circuited

⇒ A clipper
adds a dc component to the input signal
removes signal voltages above or below a specified value
both (a) and (b)
either (a) or (b)

⇒ In the circuit of figure, the switch is closed at t = 0. At t = 0⁺ the current through
0.166666666666667
2.5 A
3.1 A
0

⇒ Dynamic range of hi-fi system is at least
150 dB
120 dB
80 dB
40 dB

⇒ For the time domain response shown in figure the
lies in left half plane
lies on imaginary axis
lies along the positive real axis
may be complex or imaginary

⇒ The attenuation in a waveguide near the cut off frequency is
zero
low
high
very high