Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | When a column is subjected to an eccentric load, the stress induced in the column will be |

A. | direct stress only [Wrong Answer] |

B. | bending stress only [Wrong Answer] |

C. | shear stress only [Wrong Answer] |

D. | direct and bending stress both [Correct Answer] |

View Answer
Explanation:-
Answer : DDiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ If percentage reduction in area of a certain specimen made of material '

*A*' under tensile test is 60% and the percentage reduction in area of a specimen with same dimensions made of material '

*B*' is 40%, then

the material A is more ductile than material B

the material B is more ductile than material A

the ductility of material A and B is equal

the material A is brittle and material B is ductile

⇒ A section of beam is said to be in pure bending, if it is subjected to

constant bending moment and constant shear force

constant shear force and zero bending moment

constant bending moment and zero shear force

none of the above

⇒ Transverse fillet welds are designed for

tensile strength

compressive strength

shear strength

bending strength

⇒ A boiler shell 200 cm diameter and plate thickness 1.5 cm is subjected to internal pressure of 1.5 MN/m , then the hoop stress will be

30 MN/m2

50 MN/m2

100 MN/m2

200 MN/m2

⇒ The shear force at the ends of a simply supported beam carrying a uniformly distributed load of

*w*per unit length is.

zero at its both ends

wl at one end and - wl at the other end

wl/2 at one end and - wl/2 at the other end

wl2/2 at one end and - wl2/2 at the other end

⇒ In case of an over-reinforced beam, the depth of actual neutral axis is the same as that of the critical neutral axis.

True

False

Agree

Disagree

⇒ A steel bar 2 m long, 20 mm wide and 10 mm thick is subjected to a pull of 2 kN. If the same bar is subjected to a push of 2 kN, the Poission's ratio of the bar in tension will be __________ the Poisson's ratio for the bar in compression.

equal to

less than

greater than

none of these

⇒ When it is indicated that a member is elastic, it means that when force is applied, it will

not deform

be safest

stretch

not stretch

⇒ A rod is enclosed centrally in a tube and the assembly is tightened by rigid washers. If the assembly is subjected to a compressive load, then.

rod is under compression

tube is under compression

both rod and tube are under compression

tube is under tension and rod is under compression

⇒ The bending moment on a section is maximum where shear force is

minimum

maximum

changing sign

zero

⇒ The unit of Young's modulus is

mm/mm

kg/cm

kg

kg/cm2

⇒ The weakest section of a diamond riveting is the section which passes through

the first row

the second row

the central row

one rivet hole of the end row

⇒ A thin cylindrical shell of diameter (

*d*) length (

*l*) and thickness (

*t*) is subjected to an internal pressure (

*p*). The longitudinal stress in the shell is.

pd/t

pd/2t

pd/4t

pd/6t

⇒ A body is subjected to a direct tensile stress of 300 MPa in one plane accompanied by a simple shear stress of 200 MPa. The maximum normal stress will be

-100 MPa

250 MPa

300 MPa

400 MPa400 MPa

⇒ The bending moment in the centre of a simply supported beam carrying a uniformly distributed load of

*w*per unit length is?

zero

wl2/2

wl2/4

wl2/8

⇒ In calculating the strength of a riveted joint in tearing, shearing and crushing, the

actual diameter of rivet is used

actual diameter of hole drilled for rivet is used

mean diameter of hole drilled and rivet is used

smaller of the rivet diameter and hole diameter is used

⇒ In the below figure, the point

*C*represents

elastic limit

upper yield point

lower yield point

breaking point

⇒ The bending moment at the ends of a simply supported beam will be zero.

Yes

No

Agree

Disagree

⇒ The Poisson's ratio for steel varies from.

0.23 to 0.27

0.27 to 0.30

0.31 to 0.34

0.32 to 0.42

⇒ The extremeties of any diameter on Mohr's circle represent?

principal stresses

normal stresses on planes at 45Â°

shear stresses on planes at 45Â°

normal and shear stresses on a plane

⇒ The point of contraflexure is a point where?

shear force changes sign

bending moment changes sign

shear force is maximum

bending moment is maximum

⇒ The load at which the column just buckles, is known as

buckling load

critical load

crippling load

any one of these

⇒ In a tensile test, when the material is stressed beyond elastic limit, the tensile strain __________ as compared to the stress.

decreases slowly

increases slowly

decreases more quickly

increases more quickly

⇒ In a thick cylindrical shell subjected to an internal pressure (

*p*), the maximum radial stress at the inner surface of the shell is.

zero

p (tensile)

-p (compressive)

2p (tensile)

⇒ The limit of eccentricity is based upon no tension condition.

True

False

incorrect

none of these

⇒ The Rankine's theory for active earth pressure is based on the assumption that.

the retained material is homogeneous and cohesionless

the frictional resistance between the retaining wall and the retained material is neglected

the failure of the retained material takes place along a plane called rupture plane

all of the above

⇒ When a shaft, is subjected to torsion, the shear stress induced in the shaft varies from.

minimum at the centre to maximum at the circumference

maximum at the centre to minimum at the circumference

zero at the centre to maximum at the circumference

maximum at the centre to zero at the circumference

⇒ The modulus of elasticity for mild steel is approximately equal to

10 kN/mm2

80 kN/mm2

100 kN/mm2

210 kN/mm2

⇒ When a rectangular beam is loaded longitudinally, the shear force develops on the top layer.

Agree

Disagree

True

False

⇒ The shear force at a certain point on a beam changes sign from +ve value to -ve value or vice versa. The bending moment at that point will be zero.

True

False

Minimum

Maximum