Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | When a change in length takes place, the strain is known as |

A. | linear strain [Correct Answer] |

B. | lateral strain [Wrong Answer] |

C. | volumetric strain [Wrong Answer] |

D. | shear strain [Wrong Answer] |

View Answer
Explanation:-
Answer : ADiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ At the neutral axis of a beam, the shear stress is

zero

minimum

maximum

infinity

⇒ According to Euler's column theory, the crippling load for a column of length (

*l*) with one end fixed and the other end free is __________ the crippling load for a similar column hinged at both the ends.

equal to

less than

more than

none of these

⇒ Rupture stress is

breaking stress

maximum load/original cross-section¬al area 04)

load at breaking point/A

load at breaking point/neck area

⇒ In a beam where shear force changes sign, the bending moment will be.

zero

minimum

maximum

infinity

⇒ A beam which is fixed at one end and free at the other is called.

simply supported beam

fixed beam

overhanging beam

cantilever beam

⇒ The direct stress, across a principal plane, is known as principal stress.

Yes

No

Agree

Disagree

⇒ In a stress-strain diagram as shown in the below figure, the curve

*A*represents

mild steel

soft brass

low carbon steel

cold rolled steel

⇒ In riveted boiler joints, all stresses, shearing, bearing and tensile are based on the

size of rivet

size of the drilled or reamed hole

average of size of rivet and hole

smaller of the two

⇒ The maximum deflection of a fixed beam of length

*l*carrying a central point load

*W*is.

Wl/48 EI

WI3/96 EI

WI3/192 EI

WI3/384 EI

⇒ Transverse fillet welds are designed for

tensile strength

compressive strength

shear strength

bending strength

⇒ The assumption made in the theory of the reinforced cement concrete beam is that

all the tensile stresses are taken up by the steel reinforcement only

there is a sufficient bond between steel and concrete

the steel and concrete are stressed within its elastic limit

all of the above

⇒ The ratio of direct stress to volumetric strain in case of a body subjected to three mutually perpendicular stresses of equal intensity, is equal to

Young's modulus

bulk modulus

modulus of rigidity

modulus of elasticity

⇒ The neutral axis of a beam is subjected to __________ stress.

zero

maximum tensile

minimum tensile

maximum compressive

⇒ The tensile strength of ductile materials is __________ its compressive strength.

equal to

less than

greater than

none of these

⇒ The maximum shear stress, in the given figure, is equal to __________ of the Mohrs circle.

radius

diameter

circumference

area

⇒ The total strain energy stored in a body is called proof resilience.

Agree

Disagree

decrease

None of these

⇒ The point of contraflexure occurs in?

cantilever beams

simply supported beams

overhanging beams

fixed beams

⇒ A section of beam is said to be in pure bending, if it is subjected to

constant bending moment and constant shear force

constant shear force and zero bending moment

constant bending moment and zero shear force

none of the above

⇒ For which material the Poisson's ratio is more than unity

steel

copper

aluminum

cast iron

⇒ The bending moment of a cantilever beam of length

*l*and carrying a uniformly distributed load of

*w*per unit length is __________ at the fixed end.

wl/4

wl/2

wl

wl2/2

⇒ A shaft revolving at ω rad / s transmits torque (

*T*) in N-m. The power developed is.

T.Ï‰ watts

2 Ï€ TÏ‰ watts

2Ï€ TÏ‰/75 watts

watts

⇒ In order to avoid tearing off the plate at an edge, the distance from the centre of the rivet hole to the nearest edge of the plate (i.e. margin) should be (where

*d*= Diameter of rivet hole in mm)

d

1.5 d

2 d

2.5 d

⇒ The value of shear stress which is induced in the shaft due to the applied couple varies

from maximum at the centre to zero at the circumference

from zero at the centre to maximum at the circumference

from maximum at the centre to mini-mum at the cricumference

from minimum at the centre to maxi-mum at the circumference

⇒ The strength of a riveted joint is equal to the.

pull required to tear off the plate per pitch length (Pt)

pull required to shear off the rivet per pitch length (Ps)

pull required to crush the rivet per pitch length (Pc)

minimum value of Pt, Ps or Pc

⇒ When a bar of length

*l*and diameter

*d*is rigidly fixed at the upper end and hanging freely, then the total elongation produced in the bar due to its own weight is (where

*w*= Weight per unit volume of the bar).

wl/2E

wl2/2E

wl3/2E

wl4/2E

⇒ The bending moment diagram for a simply supported beam loaded in its centre is.

a right angled triangle

an issoscles triangle

an equilateral triangle

a rectangle

⇒ The elasticity of various materials is controlled by its

ultimate tensile stress

proof stress

stress at yield point

stress at elastic limit

⇒ When a body is subjected to three mutually perpendicular stresses, of equal intensity, the ratio of direct stress to the corresponding volumetric strain is known as.

Young's modulus

modulus of rigidity

bulk modulus

Poisson's ratio

⇒ In the below figure, the point

*B*represents upper yield point.

Correct

Incorrect

Maximum

None of these

⇒ The bending moment at the ends of a simply supported beam will be zero.

Yes

No

Agree

Disagree