Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | When a body is subjected to a direct tensile stress (σ) in one plane, then tangential or shear stress on an oblique section of the body inclined at an angle θ to the normal of the section is |

A. | Ïƒ sin 2Î¸ [Wrong Answer] |

B. | Ïƒ cos 2Î¸ [Wrong Answer] |

C. | Ïƒ/2 sin 2Î¸ [Correct Answer] |

D. | Ïƒ/2 cos 2Î¸ [Wrong Answer] |

View Answer
Explanation:-
Answer : CDiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ For a 25 mm hole drilled in plates, the diameter of rivet shank should be?

23mm

24.5mm

25mm

26mm

⇒ The thermal stress in a bar is __________ proportional to the change in temperature.

directly

indirectly

both (a) and (b)

none of these

⇒ A steel bar 2 m long, 20 mm wide and 10 mm thick is subjected to a pull of 2 kN. If the same bar is subjected to a push of 2 kN, the Poission's ratio of the bar in tension will be __________ the Poisson's ratio for the bar in compression.

equal to

less than

greater than

none of these

⇒ In the below figure, the point

*B*represents upper yield point.

Correct

Incorrect

Maximum

None of these

⇒ In the below figure, curve

*C*represents soft brass.

True

False

Maximum

Minimum

⇒ The weakest section of a diamond riveting is the section which passes through

the first row

the second row

the central row

one rivet hole of the end row

⇒ In the tensile test, the phenomenon of slow extension of the material, i. e. stress increasing with the time at a constant load is called

creeping

yielding

breaking

plasticity

⇒ The strength of the shaft is judged by the torque transmitted by the shaft.

Yes

No

Both (a) and (b)

None of these

⇒ A pressure vessel is said to be a thick shell, when.

it is made of thick sheets

the internal pressure is very high

the ratio of wall thickness of the vessel to its diameter is less than 1/10.

the ratio of wall thickness of the vessel to its diameter is greater than 1/10.

⇒ The maximum deflection of a fixed beam carrying a central point load lies at.

fixed ends

centre of beam

l/3 from fixed ends

none of these

⇒ A thin spherical shell of diameter (

*d*) and thickness (

*t*) is subjected to an internal pressure (

*p*). The stress in the shell material is.

pd/t

pd/2t

pd/4t

pd/8t

⇒ When a body is subjected to three mutually perpendicular stresses, of equal intensity, the ratio of direct stress to the corresponding volumetric strain is known as.

Young's modulus

modulus of rigidity

bulk modulus

Poisson's ratio

⇒ Euler's formula holds good only for?

short columns

long columns

both short and long columns

weak columns

⇒ The assumption made in Euler's column theory is that.

the failure of column occurs due to buckling alone

the length of column is very large as compared to its cross-sectional dimensions

the column material obeys Hooke's law

all of the above

⇒ When two shafts of same length, one of which is hollow, transmit equal torques and have equal maximum stress, then they should have equal.

polar moment of inertia

polar modulus

diameter

angle of twist

⇒ The extremeties of any diameter on Mohr's circle represent?

principal stresses

normal stresses on planes at 45Â°

shear stresses on planes at 45Â°

normal and shear stresses on a plane

⇒ The breaking stress is __________ the ultimate stress.

equal to

less than

greater than

none of these

⇒ When a material is loaded within elastic limit, the material will regain its shape and size when the load is removed.

Agree

Disagree

Maximum

Minimum

⇒ When a body is subjected to a direct tensile stress (σ) in one plane, then normal stress on an oblique section of the body inclined at an angle θ to the normal of the section is

Ïƒ cos Î¸

Ïƒ cos2 Î¸

Ïƒ sin Î¸

Ïƒ sin2 Î¸

⇒ A localised compressive stress at the area of contact between two members is known as.

tensile stress

bending stress

crushing stress

shear stress

⇒ Two solid shafts '

*A*' and '

*B*' are made of the same material. The shaft '

*A*' is of 50 mm diameter and shaft '

*B*' is of 100 mm diameter. The strength of shaft '

*B*' is __________ as that of shaft

*A*.

one-half

double

four times

eight times

⇒ The centre to centre distance, between two consecutive rivets in a row, is called

margin

pitch

back pitch

diagonal pitch

⇒ A lap joint is always in __________ shear.

single

double

fourth

six

⇒ The shear force of a cantilever beam of length

*l*carrying a uniformly distributed load of

*w*per unit length is __________ at the free end.

zero

wl/4

wl/2

wl

⇒ For the beam shown in the below figure, the shear force at

*A*is equal to

wl/6

wl/3

wl

2 wl/3

⇒ The Poisson's ratio for steel varies from.

0.23 to 0.27

0.27 to 0.30

0.31 to 0.34

0.32 to 0.42

⇒ In a belt drive, the pulley diameter is doubled, the belt tension and pulley width remaining same. The changes required in key will be

increase key length

increase key depth

increase key width

double all the dimensions

⇒ The shear force and bending moment are zero at the free end of a cantilever beam, if it carries a.

point load at the free end

point load at the middle of its length

uniformly distributed load over the whole length

none of the above

⇒ Tensile strength of a material is obtained by dividing the maximum load during the test by the

area at the time of fracture

original cross-sectional area

average of (a) and (b)

minimum area after fracture

⇒ The load required to produce a unit deflection in a spring is called.

flexural rigidity

torsional rigidity

spring stiffness

Young's modulus