Question is ⇒ What will be FSV in 2 bit BCD D/A converter is a weighted resistor type with ER = 1V, R = 1 MΩ and Rf = 10KΩ, Options are ⇒ (A) 0.99 V, (B) 0.9 V, (C) 0.1 V, (D) 0, (E) , Leave your comments or Download question paper.

Question is ⇒ What will be FSV in 2 bit BCD D/A converter is a weighted resistor type with ER = 1V, R = 1 MΩ and Rf = 10KΩ, Options are ⇒ (A) 0.99 V, (B) 0.9 V, (C) 0.1 V, (D) 0, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	What will be FSV in 2 bit BCD D/A converter is a weighted resistor type with E_R = 1V, R = 1 MΩ and R_f = 10KΩ
A.	0.99 V [Correct Answer]
B.	0.9 V [Wrong Answer]
C.	0.1 V [Wrong Answer]
D.	0 [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒

Assertion (A): Manufacturer's quote h parameters of transistor

Reason (R): h parameters of a transistor are easiest to measure

Both A and R are correct and R is correct explanation for A
Both A and R are correct but R is not correct explanation for A
A is correct R is wrong
A is wrong R is correct

⇒ A rectangular waveguide measures 3 x 4.5 cm internally and has a 10 GHz signal propagated in it. Calculate the wave impedance for dominant mode.
130 p
1.3 p
120 p
12 p

⇒ The circuit in figure has reached steady values with switch open. If switch is closed at t = 0 the voltage across 2 μF capacitance at t = 0^{+zero
4 V
6 V
10 V}

⇒ Which mode has the minimum cutoff frequency in rectangular wave guides?
TE₁₁
TE₁₀
TE₀₁
TE₂₀

⇒ For generating 1 MHz frequency signal, the most suitable circuit is
phase shift oscillator
weinbridge oscillator
colpitt's oscillator
clapp oscillator

⇒ The number of inputs and outputs in a full adder are
2 and 1
2 and 2
3 and 3
3 and 2

⇒ Consider the following features of monochrome TV

Number of lines per picture 625
Interlace ratio 2 : 1
Aspect ratio 4 : 3
Channel bandwidth 8 MHz

As regards CCIR system B, which of the above are correct?
1, 2, 3, 4
1, 2, 3
1, 2, 4
2, 3, 4

⇒ A Wien bridge oscillator uses Wien bridge for
tuning and phase shift
tuning
phase shift
either tuning or phase shift

⇒ In 8086 the number of lines on which data and address is multiplexed is
8
16
20
32

⇒ Find 'X' in the circuit bel
p(0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 15)
0
Σ(14)
1

⇒ A counter has 4 flip flops. It divides the input frequency by
4
2
8
16

⇒ An ac tachometer has a drag cup construction so that
rotor inertia is low
rotor body is conducting
rotor is easy to fabricate
both (a) and (b)

⇒ Satellite communication uses frequencies in the range of
3 to 6 GHz
3-10 MHZ
10-50 GHz
100-200 GHz

⇒ The disadvantage of counter type ADC as compared to comparator ADC is that
resolution is low
conversion time is more
circuit is more complex
stability is low

⇒ The polarization of dielectric materials results in
production of eddy currents
creation of electric dipoles
absorption of electrons
release of high velocity protons

⇒ The 8085 instruction 'PUSH PSW' belongs to the group
data transfer
arithmetic
logic
none of the above

⇒ Which of the following is a valid variable in FORTRAN 77?
0.125
ALPHA -3
ALPHA 3
BALPHAC

⇒ In log magnitude Bode diagram the slope of high frequency asymptote of (1 + jωT) is
20 dB per decade
10 dB per decade
20 dB per octave
10 dB per octave

⇒ The rotation of direction of E field of a linearly polarized wave passing through a magnetised ferric medium is called
Lorentz rotation
Faraday rotation
Steinmitz rotation
Fleming's rotation

⇒

Match the following:

	List I (Electron spin)		List II (Phenomenon)
A.	↑↑↑↑	1.	Antiferromagnetism
B.	↑↓↑↓	2.	Ferrimagnetism
C.	↑↓↑↓	3.	Ferromagnetism

A-1, B-2, C-3
A-3, B-2, C-1
A-2, B-3, C-1
A-3, B-1, C-2

⇒ In the circuit of figure, Thevenin's resistance is 10 &
25 Ω
10 Ω
13.33 Ω
6 Ω

⇒ A stepper motor is
a two phase induction motor
is a kind of rotating amplifier
is an electromagnetic transducer used to convert an angular position of shaft into electrical signal
is an electromechanical device which actuates a train of step angular movements in response to a train of input pulses on one to one basis

⇒

Match the following:

	List I		List II
A.	h_ie	1.	siemens
B.	h_oe	2.	no units
C.	h_fe	3.	ohms

A-1, B-2, C-3
A-3, B-1, C-2
A-2, B-1, C-3
A-3, B-2, C-1

⇒ The maximum counting range of a four stage counter using IC 74193 is
0 to 1023
0 to 4093
0 to 65535
0 to 131071

⇒ Which data transfer scheme is used when large block of data is to be transferred in a computer?
DMA
Programmed data transfer
Either (a) or (b)
Neither (a) nor (b)

⇒ Poles and zeros of a driving point function of a network are simple and alternate on jω axis. The network consists of
R and C
L and C
R and L
R, L and C

⇒ In VCR the luminance signal is recorded by
frequency modulation
phase modulation
amplitude modulation
direct recording

⇒ The z-transform of a particular signal is gi
casual and stable
non-casual and stable
non-casual and unstable
casual and unstable

⇒

Assertion (A): The use of 2's complement has simplified the computer hardware for arithmetic operations

Reason (R): 2's complement is obtained by adding 1 to 1's complement.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ The statement IMPLICIT INTEGER (A - F) in FORTRAN identifies
all variable names which begin with A, B, C, D, E or F as being of integer type
all character names which begin with A, B, C, D, E, or F as being of integer type
all variable names which begin with A and have 6 characters
none of the above