Question is ⇒ What is the minimum value of VSWR that may exist on a transmission line?, Options are ⇒ (A) Less than zero, (B) Zero, (C) One, (D) 10, (E) , Leave your comments or Download question paper.

Question is ⇒ What is the minimum value of VSWR that may exist on a transmission line?, Options are ⇒ (A) Less than zero, (B) Zero, (C) One, (D) 10, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	What is the minimum value of VSWR that may exist on a transmission line?
A.	Less than zero [Wrong Answer]
B.	Zero [Wrong Answer]
C.	One [Correct Answer]
D.	10 [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ As per time displacement theorem in Laplace transformation, displacement in the time domain by T becomes
division by s in the s domain
division by e^-sT in the s domain
multiplication by s in the s domain
multiplication by e^-sT in the s domain

⇒ When a superheterodyne receiver is tuned to 455 kHz, its local oscillator provides a mixer with the input at 1010 kHz. The image frequency is
555 kHz
1010 kHz
1465 kHz
1920 kHz

⇒ Race condition occurs in
synchronous circuit
asynchronous circuit
combinational circuit
all the Digital circuit

⇒ In FM 'guard band' is provided
to limit upper frequency limit
to limit lower frequency limit
so that there is less adjacent channel interference
to limit transmitted power of a station

⇒

Match the following:

	List I (BJT amplifier)		List II (Characteristics)
A.	CE	1.	good voltage gain, good current gain
B.	CC	2.	voltage gain less than 1, high current gain
C.	CB	3.	current gain less than 1, voltage gain high

A-1, B-2, C-3
A-1, B-2, C-3
A-3, B-1, C-2
A-3, B-2, C-1

⇒ The figure of merit for a logic family is
gain band width product
(propagation delay time) (power dissipation)
(fan out) (power dissipation)
(noise margin) (power dissipation)

⇒ Transconductance indicates the
control of output voltage by input voltage
control of output current by input voltage
control of input voltage by output current
control of input current by input voltage

⇒ State variable formulation is very suitable for computer solution.
TRUE
FALSE

⇒ In a JK Master slave flip flop
both master and slave are positively clocked
both master and slave are negatively clocked
master is positively clocked and slave is negatively clocked
master is negatively clocked and slave is positively clocked

⇒ The sensitivity of a potentiometer can be increased by
increasing the length of wire
decreasing the length of wire
increasing the current in the wire
decreasing the current in the wire

⇒ State variables which describe a system are a unique set.
TRUE
FALSE

⇒ In Maxwell's bridge the unknown inductance is measured by comparing it with a standard capacitor.
TRUE
FALSE

⇒ The series element of a band stop filter is
capacitive
inductive
parallel combination of L and C
series combination of L and C

⇒ L/C has the dimension of
time
capacitance
inductance
resistance

⇒ In the expression b = 2.1 / 1.2 * 3.1 + 3 / 7.1 * 6 which operation would have the first priority in C?
2.1 / 1.2
1.2 * 3.1
2.1 / 1.2 * 3.1
3 / 7.1

⇒ An average response rectifier type electronic voltameter has a d.c. voltage of 10 V applied to it. What is the meter reading?
7.1 V
10 V
11.1 V
22.2 V

⇒ A 1000 kHz carrier is simultaneously modulated with 300 Hz, 800 Hz and 2 kHz audio sine waves. Which of the following frequency is least likely to be present in the output?
1002 kHz
1000 kHz
999.2 kHz
998.0 kHz

⇒ In envelope detection of an AM waveform
One side band and full-ampiitude carrier are needed
Both side bands and full-amplitude carrier are needed
Only two side bands are needed
Upper side band and part of carrier are needed

⇒ The numerical value of directivity of current element of half-wave dipole is 1.76 and 2.15 dB respectively. The directive gain of half-wave dipole over current element will be
3.91 dB
1.95 dB
0.39 dB
0.195 dB

⇒ In a bipolar transistor
recombination in base regions of both n-p-n and p-n-p transistor is low
recombination in base regions of both n-p-n and p-n-p transistors is high
recombination in base region of n-p-n transistor is low but that in p-n-p transistor is high
recombination in base region of p-n-p transistor is low but that in n-p-n transistor is high

⇒ A frequency doubler has an FM signal input at 13 MHz with a deviation of 5 kHz. The output frequency of the carrier will be
26 kHz
260 kHz
26 MHz
260 MHz

⇒ In PCM, if the number of quantization levels is increased from 4 to 64, then the bandwidth requirement will approximately be increased __________ times.
8
16
3
32

⇒ Is the interrupt-enable flag?
Low
High
Never
None

⇒ The circuit shown in figure, will act as an ideal current source with respect to terminals A and B, when frequenc
zero
1 rad/s
4 rad/s
16 rad/s

⇒ For a reactance function H(s), the slope dH (jω)/dω is
0
always positive
always negative
either 0 or positive

⇒ In the following transistor circuit V_BE = 0. 7 V, r_c = 25mV/I_E, and β and the capacitance are very l
-180
-120
-90
-60

⇒ Noise generated in a resistor is also known as
partition noise
white noise
thermal noise
shot noise

⇒ In the periodic train of rectangular pulses F₀ = (V₀/T)d
TRUE
FALSE

⇒ Surface leakage current is a part of
reverse current
forward current
reverse breakdown
forward breakdown

⇒ A thyristor has a turn on time of 6 μs. If the anode circuit is inductive, the turn on time will be
6 μs
less than 6μs
more than 6 μs
either 6 μs or less

Users Also Read
Previous Papers

Aptitude

Reasoning

Gen.Knowledge

Speak English

English / Verbal

Online / Mock Test

Vedic Math