Question is ⇒ What is the major cause of creeping in an energy-meter?, Options are ⇒ (A) Over compensation for friction, (B) Mechanical vibrations, (C) Excessive voltage across the potential coil, (D) Stray magnetic fields, (E) , Leave your comments or Download question paper.

Question is ⇒ What is the major cause of creeping in an energy-meter?, Options are ⇒ (A) Over compensation for friction, (B) Mechanical vibrations, (C) Excessive voltage across the potential coil, (D) Stray magnetic fields, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	What is the major cause of creeping in an energy-meter?
A.	Over compensation for friction [Correct Answer]
B.	Mechanical vibrations [Wrong Answer]
C.	Excessive voltage across the potential coil [Wrong Answer]
D.	Stray magnetic fields [Wrong Answer]
View Answer 7 -4 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In a series circuit with X_L constant and R variable the current locus lies in the third quadrant.
TRUE
FALSE

⇒ RF amplifiers are used in radio receivers for
improved image frequency rejection
improved rejection of adjacent unwanted signals
prevention of re-radiation of the local oscillator through the antenna of the receiver
all of the above

⇒ Consider the following statements about root locus

The intersection of root locus branches with the imaginary axis can be determined by the use of Routh criterion
Segments of real axis having an odd number of real axis open loop poles plus zeros to their right are not parts of root locus
The number of root locus branches terminating on infinity is always zero

Which of the above statements are correct?
1, 2 and 3
1 and 2 only
1 only
2 and 3 only

⇒ The effective electrical length of an antenna is __________ its physical length
greater than
equal to
less than
none of the above

⇒ Companding is used in PCM to
reduce bandwidth
increasing S/N ratio
get almost uniform S/N ratio
increase bandwidth

⇒ For an RC admittance function Y,
Y(∞) < Y(0)
Y(0) < Y(∞)
Y (∞) may be lesser or greater than Y(0)
Y(∞) = Y(0)

⇒ A balanced modulator is used in the generation of which of the following?
DSB-SC signal
FM signal
PM signal
PAM signal

⇒

Assertion (A): A PROM is a user programmable ROM.

Reason (R): After programming PROM behaves like ROM.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ One eV = 1.602 x 10^-19 joules.
TRUE
FALSE

⇒ A single phase half wave controlled rectifier circuit has an R-L load. A freewheeling diode is also in the circuit. When freewheeling diode is conducting the SCR
is forward biased
is reverse biased
may be forward biased or reverse biased
forward biased initially but reverse biased afterwards

⇒ In a BJT amplifier circuit the size of coupling capacitor depends on
lowest frequency
highest frequency
average of lowest and highest frequencies
none of the above

⇒ For dc the current through coupling capacitor in CE amplifier circuit is
very high
high
low
zero

⇒ An arithmetic statement in C must be
integer mode arithmetic statement
real mode arithmetic statement
mixed mode arithmetic statement
any of the above

⇒ The resistance of the aluminium conductor (r = 2.83 x 10^-8 Ωm) in figur
0.001 Ω
less than 0.001 Ω
more than 0.001 Ω
more than 0.002 Ω

⇒ A series RLC circuit has Q = 5. A voltage of 10 V rms is applied to it. At resonance, the voltage across C is
10 V rms
10 V peak
50 V rms
50 V peak

⇒ In figure the total inductance of the circui
L₁ + L₂
L₁ + L₂ - M
L₁ + L₂ - 2M
L₁ + L₂ + M

⇒ The root locus branches
start from open loop poles and terminate at zeros
start from open loop zeros and terminate at poles
may start from pole or zero and terminate at another pole or zero
none of the above

⇒ A Weston frequency meter is
moving coil instrument
moving iron instrument
dynamometer instrument
induction instrument

⇒ Considerable ionization occurs between the range
50 km to 400 km
100 to 400 km
50 km to 250 km
10 to 50 km

⇒ If 8085 is required to add two 32 bit numbers, the numbers of addition sequences is
1
2
4
8

⇒ What is the characteristic impedance at 10 MHz?
547.7 Ω
54.7 Ω
5.47 Ω
.547 Ω

⇒ A signal m(t) with bandwidth 500 Hz is first multiplied by a signal g(t) w
δ(t)
m(t)
0
m(t) δ(t)

⇒ The addressing mode depicted in the given figur
direct
register
register indirect
immediate

⇒ A source generates three symbols with probabilities 0.25, 0.25, 0.50 at a rate of 3000 symbols per second. Assuming independent generation of symbols, the most efficient source encoder would have average bit rate is as
6000 bits/sec
4500 bits/sec
3000 bits/sec
1500 bits/sec

⇒ In 8085 the time required to add two 32 bit numbers is (if clock frequency is 5 MHz)
about 1 ns
about 1 μs
about 30 μs
about 100 μs

⇒ For the system in the given figure. The transfer function C(s)/R(s
G₁ + G₂ + 1
G₁ G₂ + 1
G₁ G₂ + G₂ + 1
G₁ G₂ + G₁ + 1

⇒ The superposition theorem is applicable to
linear, non-linear and time variant responses
linear and non-linear resistors only
linear responses only
none of the above

⇒ The thermal resistance of a BJT is about
100° C/W
200° C/W
20° C/W
2° C/W

⇒ The most commonly used bias in BJT amplifier circuits is
voltage divider bias
emitter bias
collector bias
collector feedback bias

⇒ In a full wave diode rectifier circuit each diode carries current for
90° in each cycle
180° in each cycle
270° in each cycle
360° in each cycle