Question is ⇒ Two stoke engine is preferred for small vehicles because, Options are ⇒ (A) Fuel consumption is low, (B) Shock and vibrations are less, (C) Its size is small, (D) It is easy to control, (E) , Leave your comments or Download question paper.

Question is ⇒ Two stoke engine is preferred for small vehicles because, Options are ⇒ (A) Fuel consumption is low, (B) Shock and vibrations are less, (C) Its size is small, (D) It is easy to control, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Two stoke engine is preferred for small vehicles because
A.	Fuel consumption is low [Wrong Answer]
B.	Shock and vibrations are less [Wrong Answer]
C.	Its size is small [Correct Answer]
D.	It is easy to control [Wrong Answer]
View Answer 4 -5 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In 'V' type engines the included angle between two banks of cylinders is
450
600
1300
900

⇒ During combustion the pressure in the cylinder may increase to as much as
50 Kg/cm2
400 Kg/cm2
10 Kg/cm2

⇒ The brake pipe in hydraulic brakes is made up of
PVC
Steel
Rubber
Copper

⇒ In the Hotchkiss drive, the rear end torque is absorbed by the
Torque tube
Rear springs
Radius rods

⇒ The metering rod is designed to vary the size of which jets
High speed jets
Accelerating jets
Float level jets
Idle jets

⇒ The temperature of the compressed air should be .............. of the fuel
Below the flash point
Above the flash point
Above the fire point
Between the fire and flash point

⇒ To equalize tyre wear, it is suggested that tyres be rotated from one wheel to another every
80 kms
8000 kms
800 kms

⇒ The power train transmits power from the engine to the
Crank shaft
Rear wheels
Front wheels
Steering gear

⇒ In the high gear in the transmission, main shaft turns at the same speed as the
Idler shaft
Counter shaft
Clutch shaft

⇒ If the connecting rod longer, the side thrust of the piston is
Increased
Constant
Decreased

⇒ Spur gear type of differential is unsuitable for passenger car applications because
It results in a very costly rear axle assembly
The large transmission losses due to spur gears
Large dimension of final drive housing resulting in reduced ground clearance
Centre of gravity of the vehicle is raised

⇒ In the hydraulic brake system, movement of a piston in the master cylinder produces hydraulic pressure which causes movement of the
Wheel cylinder pistons
Brake pedal
Brake cam

⇒ In the multiplier type of brake, the diaphragm acts directly on the hydraulic piston in the
Master cylinder
Wheel cylinder
Multiplier unit

⇒ Synchronizing is designed to prevent gear clash when shifting into
First and reverse
First and second
Second and high

⇒ Twisting and untwisting of the crankshaft is called
Torsional vibration
Power impulsion
Torsional balance

⇒ As the number of cylinders in multi cylinder engines increases the power to weight ratio .........
Remains the same
Increases
Becomes zero
Decreases

⇒ The power train includes the clutch, propeller shaft, differential and ................
Steering gear
Front axles
Chassis
Transmission

⇒ Clutch chattering or grabbing is noticeable
At low speed
When engaging the clutch
When accelerating
During idle

⇒ Engine torque is highest at
High speed
Low speed
Intermediate speed

⇒ IHP minus FHP equals
BHP
SAF HP
m.e.p

⇒ To correct heavy flank contact on the ring gear teeth
Move the drive pinion in
Move the drive pinion out
Move the ring gear out
Adjust back lash as necessary

⇒ In a vacuum suspended unit, when the brakes are on, the piston or diaphragm has on both sides of it
Atmospheric pressure
Vacuum
Hydraulic pressure

⇒ The most popular drive at the drive axle for the passenger car is
Straight bevel gear
Spiral bevel gear
Worm gear drive
Hypoid drive

⇒ In the diaphragm clutch inward movement of the throw out bearing causes the diaphragm spring to
Dish inward
Expand
Contract

⇒ With an increase in temperature the resistance of carbon is
Unchanged
Decreased
Increased

⇒ The slip joint permits a change in the
Length of shaft
Speed of rotation
Angle of drive

⇒ Aluminium alloy pistons are preferred because
They are good absorbers of shock
They are having less weight
They have good water resistance
They are very strong in tension

⇒ In the case of brake linings saturants and bonding materials are used to
Facilitate moulding and curing of brake linings
To improve the heat dissipating capacity of linings
To give a constant coefficient of friction up to 800 C
To make the lining material impervious to moisture and oil and to ensure a steady coefficient of friction up to 3000 C

⇒ In the power assisted type of brake the bellows applies force to the master cylinder piston
Through diaphragm linkage
Directly
Through mechanical linkage

⇒ The approximate ratio of effort applied : effort available from servo system is
1:1
3:1
1:4
10:1