Question is ⇒ Two port circuits are connected in parallel. To determine the response, it is more convenient to use, Options are ⇒ (A) O.C. impedance parameters, (B) S.C. admittance parameters, (C) ABCD parameters, (D) <i>h</i> parameters, (E) , Leave your comments or Download question paper.

Question is ⇒ Two port circuits are connected in parallel. To determine the response, it is more convenient to use, Options are ⇒ (A) O.C. impedance parameters, (B) S.C. admittance parameters, (C) ABCD parameters, (D) <i>h</i> parameters, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Two port circuits are connected in parallel. To determine the response, it is more convenient to use
A.	O.C. impedance parameters [Wrong Answer]
B.	S.C. admittance parameters [Correct Answer]
C.	ABCD parameters [Wrong Answer]
D.	h parameters [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which is known as flash converter?
Weighted resistor D/A converter
Parallel A/D converter
Stair step A/D converter
Up-down counter type A/D converter

⇒ In a synchro error detector, the output voltage is proportional to [ω(t)]ⁿ, where ω(t) is the rotor velocity and n equals :
-2
-1
1
2

⇒ Double spotting in a receiver is due to
poor sensitivity of RF amplifier
high gain of IF amplifier
inadequate image frequency rejection
all of the above

⇒ An instruction using immediate addressing mode in 8085 is
2 bytes long
3 bytes long
2 or 3 bytes long
1 or 2 or 3 bytes long

⇒ The frequency response of an ideal tuned amplifier should be as represented in figur
A
B
C
D

⇒ The number of leads in a DIAC are
2
3
4
6

⇒ With on-chip decoding, n address lines can access
2n memory locations
2n² memory locations
2ⁿ memory locations
n² memory location

⇒ In 8085 microprocessor, in order to enable RST 5.5, RST 6.5 and RST 7.5 interrupts, which of the following instruction are needed?
EI only
SIM only
EI and SIM both
None

⇒ Floating gate is fabricated for making MOS
ROM
PROM
EPROM
EAROM

⇒ An ac circuit has two branches in parallel. The impedances of the two branches are equal. The p.f. of one branch is 0.8 lagging and 0.8 leading. The overall p.f. is
zero
0.5 lagging
1
0.7 lagging

⇒ A feedback network to be used with an amplifier to provide oscillation is tested and found to give an output of 0.124 V with a 0.5 V input. What percentage negative feedback should be introduced to the amplifier so that linear oscillations result?
0.0125
0.025
-0.0125
-0.025

⇒ The sum of positive real functions
is a positive real function
may be a positive real function or not
can not be a positive real function
either (b) or (c)

⇒ A square current wave of magnitude 1 A is applied to an element for 5 seconds. The voltage across the element rises linearly from 0 to final value linearly. The element is
resistance
inductance
capacitance
R and C in series

⇒ If a signal g(t) has energy E, then the energy of the signal g(2t) is equal to ...
E/2
E/4
E
2E

⇒ A TR (transmitter receiver) tube has
low loss for low power signals and high
high loss for low power signals and low loss for high level signal
low loss for both low level and high level signals
high loss for both low level and high level signals

⇒ Which of the following can be accessed only sequentially?
Floppy disk
Hard disk
Magnetic tape
ROM

⇒ Magnetic recording tape is most commonly made from
small particles of iron
silicon iron
ferric-oxide
silver nitrate

⇒ Which one of the following effects is used in measuring power?
Seeback
Ferrari
Induction
Hall

⇒ In a JFET the width of channel is controlled by
gate voltage
drain current
source current
all of the above

⇒ The 8085 microprocessor is interrupted while executing MOV instruction at location 0210 H. What is the location at which contents of register D are stored
054 CH
054 DH
054 EH
054 FH

⇒ A transmitted using AM has in modulated carrier output power of 10 KW and can be modulated to a maximum depth of 90% by a sinusoidal modulating voltage without causing overloading. Find the value to which an modulated carrier power can be increased without resulting in overloading if the maximum permitted modulating index is 40%
14 KW
12.96 KW
26.96 KW
2.96 KW

⇒ Harmonic distortion in CB amplifier may be least when the load resistance is
negligible
very low
very high
infinite

⇒ The fabrication of microstrip line is done by
photo etching
printed circuit technique
oxidation
cladding

⇒

Assertion (A): The forward dynamic resistance of p-n diode varies inversely with current.

Reason (R): The forward dynamic resistance of p-n diode varies with the operating voltage.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ The domain mode in rectangular waveguide is
TE₀₁
TE₀₂
TE₁₀
TM₁₁

⇒ Which of the following is not an internal DOS command?
VER
COPY
MEM
DATE

⇒ Which of the following real expressions is incorrect in Pascal?
Y - X
(A + B) (C + D)
X / Y - Z
P * Z - 5.0

⇒ In a N-P-N transistor, when emitter junction is forward biased and collector junction is reverse biased, the transistor will operate in
active region
saturation region
cut of region
inverted region

⇒ In a radar, the return echo arrives after the allocated pulse interval. Then
the receiver may be over loaded
the target will appear closer than its actual position
the return echo may interfere with transmitter operation
none of the above

⇒ A choke coil has a resistance to reactance ratio of 0.2. The power factor of the choke coil is
less than 0.2 lagging
less than 0.2 leading
about 1
about 0