Question is ⇒ Two function g1(t) and g2(t) with correlation of 6 has average power of 4 and 5 respectively. The power of g1(t) + g2(t) is, Options are ⇒ (A) 9, (B) 21, (C) 3, (D) 15, (E) , Leave your comments or Download question paper.

Question is ⇒ Two function g1(t) and g2(t) with correlation of 6 has average power of 4 and 5 respectively. The power of g1(t) + g2(t) is, Options are ⇒ (A) 9, (B) 21, (C) 3, (D) 15, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Two function g₁(t) and g₂(t) with correlation of 6 has average power of 4 and 5 respectively. The power of g₁(t) + g₂(t) is
A.	9 [Wrong Answer]
B.	21 [Correct Answer]
C.	3 [Wrong Answer]
D.	15 [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In following figure find V_DSQ by assuming gate current is negligible for the p-channel JFET. (if I_DQ = - 6 mA, R_S = 0, V_DD = -18 V, R_D = 2 kΩ, I_DSS = - 10 mA, I_PO = - 3 V)
4 V
- 6 V
- 10 V
6 V

⇒ A battery charger can drive a current of 5A with 1Ω resistance connected at its output. If it can charge 2 V battery at 7 A rate, its Thevenin's equivalent circuit will be
7.5 in series with 0.5 Ω resistance
1.25 V in series with 1.5 Ω resistance
7.5 V in parallel with 0.5 Ω resistance
12.5 V in parallel with 1.5 Ω resistance

⇒ Some possible disadvantages of high level modulation in TV transmitters are

Video monitor has to supply high video voltages upto several hundred volts into highly capacitive loads drawing high current at video frequencies
The grid modulated stage presents a varying load to its driver
The linearity and high video driving power present design problems

Out of above which are true?
1 only
1 and 2 only
1, 2 and 3
2 and 3 only

⇒ The cut off wavelength λ_c for TE₂₀ mode for a standard rectangles waveguide is
2/a
2a
a
2a²

⇒ Which of the following conditions should be satisfied to call an astable multivibrator circuit using discrete components as a digital circuit?

A flip-flop is always a digital circuit.
Only when we assign 1 and 0 to the high and low levels of the output, a flip-flop is called a digital circuit.
Only if the power, supply voltage is maintained at + 5 V or - 5 V, it is called a digital circuit.
Only if it is in IC form, following the technology of IC manufacture, it is called a digital circuit.

Select the correct answer from the codes given below:
1 only
2 and 3
2 only
3 and 4

⇒ In RLC circuits the state variables generally selected are
voltages across capacitors
currents through resistances and voltages across capacitors
currents through resistances and capacitances
currents through inductances and voltages across capacitances

⇒ In any two port network, input impedance is independent of load impedance.
TRUE
FALSE

⇒

Assertion (A): A quarter wave transformer is used to match a resistive load to a transmission line.

Reason (R): A quarter wave transformer is a transmission line of quarter wave length.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ In CE amplifier circuit, voltage gain is directly proportional to
β
collector supply voltage
base resistance
none of the above

⇒ In p-n-p transistor the current I_E has two components viz. I_EP due to injection of holes from p-region to n-region and I_E due to injection of electrons from n-region to p-region. Then
I_Ep and I_En are almost equal
I_Ep >> I_En
I_En >> I_Ep
either (a) or (c)

⇒ In shot noise
the current rises around mean value
the current rises to peak value, decreases to zero and then again rises
the current may become negative
the current is always less than the mean value

⇒ Noise limiter is provided on AM receivers to
reduce interfering noise due to ignition system
reduce noise due to electrical storms
reduce interference due to electrical machinery
all of the above

⇒ A resistance strain gauge is usually
wire grid type
foil type
any of these
none of these

⇒

Assertion (A): In an R-L circuit having high inductance, the rise of current is very slow.

Reason (R): The time constant of R-L circuit is L/R.

Both A and R are true and R is correct explanation of A
Both A and R are true and R is not the correct explanation of A
A is true but R is false
A is false but R is true

⇒

Match the following:

	List I (Memories)		List II (Characteristic)
A.	Static PLA	1.	erasable, programmable
B.	CCD	2.	ultra high speed
C.	ECL	3.	stores large volume of data
D.	GAL	4.	Does not need refreshing
		5.	Non-volatile

A-4, B-3, C-2, D-1
A-4, B-2, C-3, D-1
A-5, B-1, C-2, D-3
A-3, B-5, C-2, D-1

⇒ An AM wave is given by s(t)_AM = 20 (1 + 0.5 cos 10³t + 0.3 cos 10⁴ t cos 10⁶ t) the modulation index of the envelope is
0.5
0.58
0.3
0.8

⇒ What is the maximum output voltage from the 741 op-amp?
Zero
Approximately 1 V
Approximately 3 V
Approximately 5 V

⇒

Assertion (A): A p-n junction is used as rectifier.

Reason (R): A p-n junction has low resistance in forward direction and high resistance in reverse direction.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ In the television system in India, the odd and even fields are scanned
25 times each
25 times each but alternately
50 times each
50 times each but alternately

⇒ The average value of wave in figur
90 V
75 V
60 V
50 V

⇒ Given figure is the voltage transfer characteristi
an N MOS inverter with enhanced mode transistor as load
an N MOS inverter with depletion mode transistor as load
a CMOS inverter
BJT inverter

⇒ In a satellite system circular polarization is to be obtained. The antenna used is
parabolic
horn
log periodic
helical

⇒ Kelvin's double bridge is used to measure low resistances because
it has high sensitivity
there is no thermoelectric emf
resistance variation due to temperature
effect of contact and lead resistances is eliminated

⇒ The function Y = A B C + AB C + A B C + A BC is to be realized using discrete gates. The inputs available are A, B, C. We need a total of
8 gates
6 gates
10 gates
5 gates

⇒ A wire has a diameter d and resistance R. If the diameter is made 3d, the length and material remaining the same, the new value of resistance will be
R/3
3 R
R/9
9 R

⇒ The density of the dynamic RAM is
more than that of static RAM
less than that of static RAM
equal to that to static RAM
equal to or more than that of static RAM

⇒ A voltage V(t) which is a Gaussian ergodic random process with a mean of zero and a variance of 4 volt² is measured by a true rms meter. The reading will be
0
4
2
16

⇒ In an RC phase shift oscillator, the total phase shift of the three RC lead networks is
360°
180°
90°
0°

⇒ In figure, the current
0.0416666666666667
0.0833333333333333
0.166666666666667
0.333333333333333

⇒ If modulus is less than 2^N, some states of the counter are skipped by using NAND gates.
TRUE
FALSE