Question is ⇒ Transmitted voltage level is:, Options are ⇒ (A) 11, (B) 7.8, (C) 7.348 V, (D) none of these, (E) , Leave your comments or Download question paper.

Question is ⇒ Transmitted voltage level is:, Options are ⇒ (A) 11, (B) 7.8, (C) 7.348 V, (D) none of these, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Transmitted voltage level is:
A.	11 [Wrong Answer]
B.	7.8 [Wrong Answer]
C.	7.348 V [Correct Answer]
D.	none of these [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Each kilometer of travel in electromagnetic radiation means a time delay of
330 μs
33 μs
3.3 μs
0.33 μs

⇒ In order to receive a vertically polarized wave, the conductor of the dipole should be mounted
horizontally
vertically
at an angle of 45°
none of the above

⇒ In figure, S is closed at t = 0. At t = t₁, I = 1 A and di/dt = 1 A/s. Then the value of
1 H
2 H
3 H
4 H

⇒ For a plate-modulated class C amplifier the plate supply voltage is E. The maximum plate cathode voltage could be almost high as
2E
3E
4E
6E

⇒ Which of the following terms are applicable to troposcatter propagation?
Faradays rotation
SIOs
Fading
Atmospheric storms

⇒ Varactor diode is forward biased when it is used.
TRUE
FALSE

⇒ A p-n junction diode has
low forward and high reverse resistance
a non-linear v-i characteristics
zero forward current till the forward voltage reaches cut in value
all of the above

⇒ For a hollow waveguide, the axial current must necessarily be
combination of conduction and displacement current
conduction current only
time varying conduction current and displacement current
displacement current only

⇒ Which of the following is not between F₂ layer and D layer?
E layer
F₁ layer
G region
All of the above

⇒ For a full wave bridge rectifier supplied with 50 Hz a.c., the lowest ripple frequency will be
50 Hz
100 Hz
200 Hz
400 Hz

⇒ Which interrupts are masked?
5.5
6.5
7.5
None

⇒ In the circuit of figure, the source supplies, 2.25 mA. The value of R mus
5 Ω
3 Ω
1.5 Ω
0.5 Ω

⇒ The operating voltage of a megger is about
100 V
12 V
6 V
1 V

⇒ A line has an attenuation of 0.054 Np/m. The attenuation in decibels is
4.7 dB/m
0.47 dB/m
0.54 dB/m
5.4 dB/m

⇒ In a series LCR circuit the maximum inductor voltage is twice the maximum capacitor voltage however current lags by 30° and drop across the inductance is v_L = 100 sin 377t V. Assuming the resistance being 20 Ω, Find the values of the capacitance and inductance.
235 μF, 61.18 μH
230 μF, 61.18 μH
61.18 μF, 230 μH
None of the above

⇒ A TRIAC can be turned on :
by applying a positive signal to gate
by applying a negative signal to gate
by applying either positive or negative signal to gate
none of the above

⇒ Two port Z parameter not exist for the circuit if
Δz = 0
Δz
Δz = 1
always exist

⇒ A machine cycle has one clock cycle.
TRUE
FALSE

⇒ In a monolithic IC, resistors are formed from
ceramic material
manganin wire
P-type semiconductor
aluminium ribbon

⇒ A remote control of TV uses a 10 bit word. The maximum number of total commands it can transmit is
64
256
512
1024

⇒ For BJT, under saturation condition
I_C = βI_B
I_C > bI_B
I_C is independent of all other parameters
I_C < βI_B

⇒ Which of the following is not an interrupt line in 8085?
TRAP
RST 5.5
RST 7.5
RST 9.5

⇒ A rhombic antenna is a
resonant antenna
non-resonant antenna
coupled antenna
none of the above

⇒ In high power AM transmission modulation is done at
IF stage
RF power
buffer stage
oscillator stage

⇒ Two sinusoidal signals of same amplitude and frequencies 10 kHz and 10.1 kHz are added together. The combined signal is given to an ideal frequency detector. The output of the detector is
0.1 kHz sinusoidal
10.1 kHz sinusoidal
a linear function
a constant

⇒ In C-language f- = 9 is equivalent to
f = -9
f = f - 9
f = 9 - 1
-f = 9

⇒ An air-filled rectangular waveguide has dimensions 8cm x 10cm . The phase velocity of guided wave at frequency of 3 GHz for TE₁₀ mode is
1.5 x 10⁸ m/s
5.5 x 10⁸ m/s
3.46 x 10⁸ m/s
0.18 x 10⁷ m/s

⇒ The memory hierarchy in microprocessor based system is
register, cache, primary, mass, off line back up
cache, register, primary, mass, off line back up
cache, register, mass, primary, off line back up
register, cache, mass, primary, off line back up

⇒

Match the following:

	List I (Operator)		List II (Description)
A.	! =	1.	Left shift
B.	= =	2.	Right Shift
C.	< <	3.	Equal to
D.	> >	4.	Not equal to

A-1, B-2, C-3, D-4
A-2, B-3, C-4, D-1
A-4, B-1, C-3, D-2
A-4, B-3, C-1, D-2

⇒ If V_a = 10 ∠0, V_b = 10 ∠ -120° and V_c = 10 ∠ -240°, then V_a2 and V_a0 are
10 and 0 respectively
0 and 10 respectively
0 and 0
10 and 10