Question is ⇒ Transmission lines link, Options are ⇒ (A) generating station to receiving end station, (B) receiving end station to distribution transformer, (C) distribution transformer to consumer premises, (D) service points to consumer premises, (E) none of the above, Leave your comments or Download question paper.

Question is ⇒ Transmission lines link, Options are ⇒ (A) generating station to receiving end station, (B) receiving end station to distribution transformer, (C) distribution transformer to consumer premises, (D) service points to consumer premises, (E) none of the above, Leave your comments or Download question paper. Previous question Next question


Q1.	Transmission lines link
A.	generating station to receiving end station [Correct Answer]
B.	receiving end station to distribution transformer [Wrong Answer]
C.	distribution transformer to consumer premises [Wrong Answer]
D.	service points to consumer premises [Wrong Answer]
E.	none of the above [Wrong Answer]
View Answer 8 -5 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In transmission lines the cross-arms are made of
copper
wood
R.C.C.
steel

⇒ The operating voltage of extra high tension cables is upto
66 kV
11 kV
33 kV
66 kV

⇒ Constant voltage transmission entails the following disadvantage
large conductor area is required for same power transmission
short-circuit current of the system is increased
either of the above
none of the above

⇒ Which of the following is a static exciter ?
Rectifier
Rotorol
Amplidyne
D.C. separately excited generator

⇒ A gay wire
protects conductors against shortcircuiting
provides emergency earth route
provides protection against surges
supports the pole

⇒ For exact compensation of voltage drop in the feeder the booster
must be earthed
must work on line voltage
must work on linear portion of its V-I characteristics
must work on non-linear portion of its V-I characteFistics

⇒ Transmission lines link
generating station to receiving end station
receiving end station to distribution transformer
distribution transformer to consumer premises
service points to consumer premises

⇒ Floating neutral, in 3-phase supply, is undesirable because it causes
low voltage across the load
high voltage across the load
unequal line voltages across the load
none of the above

⇒ In the design of a distributor which of the following is the major consideration ?
Voltage drop
Current carrying capacity
Frequency
kVA of system

⇒ In a distribution system major cost is that of
earthing system
distribution transformer
conductors
meters

⇒ The minimum clearance between the ground and a 220 kV line is about
4.3 m
5.5 m
7.0 m
10.5 m

⇒ Overhead system can be designed for operation upto
11 kV
33 kV
66 kV
400 kV

⇒ Power system stability is least affected by
reactance of generator
input torque
losses
reactance of transmission line

⇒ The effect of ice on transmission line conductors is to increase the
transmission losses
weight of the conductor
tendency for corona
resistance to flow of current

⇒ The steel used in steel cored conductors is usually
alloy steel
stainless steel
mild steel
high speed steel

⇒ The material used for the manufacture of grounding wires is
cast iron
aluminium
stainless steel
galvanised steel

⇒ The square root of the ratio of line impedance and shunt admittance is called the
surge impedance of the line
conductance of the line
regulation of the line
none of the above

⇒ The use of strain type insulators is made where the conductors are
dead ended
at intermediate anchor towers
any of the above
none of the above

⇒ For which of the following equipment current rating is not necessary ?
Circuit breakers
Isolators
Load break switch
Circuit breakers and load break switches

⇒ Which of the following methods is used for laying of underground cables ?
Direct laying
Draw-in-system
Solid system
All of the above

⇒ Transmitted power remaining the same, if supply voltage of a D.C. 2-wire feeder is increased 100 percent, saving in copper is
25 percent
50 percent
75 percent
100 percent

⇒ Poles which carry transformers are usually
circular
I-type
A-type
H-type

⇒ Pin type insulators are generally not used for voltages beyond
1 kV
11 kV
22 kV
33 kV

⇒ Corona is likely to occur maximum in
transmission lines
distribution lines
domestic wiring
all of the above

⇒ Which of the following are connected by the service mains ?
Transformer and earth
Distributor and relay system
Distributor and consumer terminals
Distributor and transformer

⇒ If the height of transmission tower is increased, which of the following; parameters is likely to change ?
Capacitance
Inductance
Resistance
All of the above

⇒ Which of the following faults is most likely to occur in cables ?
Cross or short-circuit fault
Open circuit fault
Breakdown of cable insulation
All of the above

⇒ Which of the following relays is used on long transmission lines ?
Impedance relay
Mho's relay
Reactance relay
None of the above

⇒ As compared to a 2-wire D.C. distributor, a 3-wire distributor with same maximum voltage to earth uses only
31.25 percent of copper
33.3 percent of copper
66.7 percent of copper
125 percent of copper

⇒ By which of the following factors is the sag of a transmission line least affected ?
Current through the conductor
Ice deposited on the conductor
Self weight of conductor
Temperature of surrounding air