Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | To convert SR latch to D latch |

A. | connect both S and R to D [Wrong Answer] |

B. | connect D to S directly and D to R through inverter [Correct Answer] |

C. | connect D to R directly and D to S through inverter [Wrong Answer] |

D. | connect S to D and leave R open [Wrong Answer] |

View Answer
Explanation:-
Answer : BDiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ Which of the following is an active device?

Transformer

Silicon controlled rectifier

Electric bulb

Loudspeaker

⇒ If

*t*and

_{on}*t*are the turn on and turn off times of a thyristor, then

_{off}*t*and

_{on}*t*are almost equal

_{off}*t*>>

_{on}*t*

_{off}*t*>>

_{off}*t*

_{on}*t*is about twice

_{on}*t*

_{off}⇒ If a microstrip is enclosed in a metal enclosure

the radiation losses are increased

the radiation losses are reduced RL

the capacitance becomes zero

the inductance becomes zero

⇒ The deflection of a DArsonval galvanometer is measured through a mirror and scale. The mirror is 1 m away from the light source. The mirror is mounted on, the moving system. If mirror rotates through 0.2 rad the displacement on the scale is

0.2 m

0.4 m

0.1 m

0.05 m

⇒ System satellites orbit the Earth once in

24 hours

12 hours

1 hours

6 hours

⇒ In deriving ac equivalent circuit for an amplifier circuit we short circuit

all resistors

all transistors

all inductors

all capacitors

⇒ Which of the following materials in not an insulator?

Diamond

Graphite

Bakelite

Lucite

⇒ A 12 bit ADC is used to convert analog voltage of 0 to 10 V into digital. The resolution is

2.44 mV

24.4 mV

1.2 V

none of the above

⇒ The initial state of MOD-16 down counter is 011. After 37 clock pulses, the state of the counter will be

1011

110

101

1

⇒ In the Taylor series expansion of exp(

*x*) + sin(

*x*) about the point

*x*= p, the coefficient of (

*x*- p)

^{2}is

exp (p)

0.5 exp (p)

exp (p) + 1

exp (p) - 1

⇒ In microwave communication links, when fading due to rain attenuation occurs then technique adopted for solving the problem would include

antenna replacement and feed correction

amplitude timing and phase correction

polarization shifting and code diversity

path diversity and frequency diversity

⇒ An input voltage V(

*t*) = 10 2 cos (

*t*+ 10°) + 10 3 cos (2

*t*+ 10°)

*V*is applied to a series combination of resistance R = 1 kΩ inductance L = 1H. The resulting steady-state current

*i*(

*t*) in ampere is

10 cos (

*t*+ 55°) + 10 cos (2

*t*+ 10° tan

^{-1}2)

10 cos (

*t*+ 55°) + 103/2 cos (2

*t*+ 55°)

10 cos (

*t*- 35) + 10 cos (2

*t*+ 10° - tan

^{-1}2)

10 cos (

*t*- 35) + 103/2 cos (2

*t*+ 35°)

⇒ Use of high permeability core in moving iron instrument helps in

reducing size of meter

increasing sensitivity

reducing temperature error

all of the above

⇒ Beamwidth of an antenna depends upon

shape of radiation pattern

dimensions

wavelength

all of the above

⇒ For satellite communication, the frequency should be

equal to the critical frequency

more than the critical frequency

less than the critical frequency

none of these

⇒ The factor n in the equation for calculating current for a silicon diode is

1

2

2.5

2 for low levels of current and 1 for high levels of current

⇒ The output of a Mealy system is 1 if there has been a pattern of 11000, otherwise 0. The minimum state for this system is :

4

5

6

7

⇒ RMS value of

*i*(

*t*) = 10[1 + sin (-

*t*)] is

10

10/2

l50

102

⇒ A coil is connected across a 200 V, 50 Hz supply and takes a current of 10 A. The loss in the coil is 1000 W. The impedance and resistance of the coil are

10 Ω, 8 Ω

15 Ω, 8 Ω

20 Ω, 10 Ω

30 Ω, 15 Ω

⇒ The modulation index is, if

*f*= 500 Hz, Δ

_{m}*f*= 2.25 kHz

2.25

4.5

9

18

⇒ In a FM waveform, the side bands are spaced at intervals equal to

four times the modulating frequency

twice the modulating frequency

half the modulating frequency

modulating frequency

⇒ In a receiver, which of the following device has IF input but RF output?

Demodulator

Loudspeaker

Audio amplifier

Frequency changer

⇒ Which of these triggering methods for series connected SCRs use LASCR in the gate circuit?

Resistance triggering

Simultaneous triggering

Sequential triggering

Optical triggering

⇒ Loading effect is primarily caused by instruments having

high resistance

high sensitivity

low sensitivity

high range

⇒ The IF stage of a receiver employs

capacitive coupling

impedance coupling

double-tuned transformer coupling

single-tuned transformer coupling

⇒ Which of the following is not correct in C?

6 / 4 = 1

2 / 5 = 0

2.0 / 5 = 0

2.0 / 5.0 = 0.4

⇒ For maximum transfer of power, internal resistance of the source should be

equal to load resistance

less than the load resistance

greater than the load resistance

none of the above

⇒ In the given figure

A

B

A + B + C

ABC

⇒ Two capacitors each of capacitance C and breakdown voltage V are joined in series. The capacitance and breakdown voltage of the combination is

0.5 C and 2 V

0.5 C and 0.5 V

C and V

2 C and 2 V

⇒ For a stable system having two or more gain crossover frequencies the phase margin is measured at the highest crossover frequency.

TRUE

FALSE