Question is ⇒ Three analog signals, having bandwidths 1200 Hz, 600 Hz, 600 Hz are sampled at their Nyquist rates, encoded with 12 bit words, and time division multiplexed. The bit rate for the multiplexed signal is, Options are ⇒ (A) 115.2 kbps, (B) 28.8 kbps, (C) 57.6 kbps, (D) 38.4 kbps, (E) , Leave your comments or Download question paper.

Question is ⇒ Three analog signals, having bandwidths 1200 Hz, 600 Hz, 600 Hz are sampled at their Nyquist rates, encoded with 12 bit words, and time division multiplexed. The bit rate for the multiplexed signal is, Options are ⇒ (A) 115.2 kbps, (B) 28.8 kbps, (C) 57.6 kbps, (D) 38.4 kbps, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Three analog signals, having bandwidths 1200 Hz, 600 Hz, 600 Hz are sampled at their Nyquist rates, encoded with 12 bit words, and time division multiplexed. The bit rate for the multiplexed signal is
A.	115.2 kbps [Wrong Answer]
B.	28.8 kbps [Wrong Answer]
C.	57.6 kbps [Correct Answer]
D.	38.4 kbps [Wrong Answer]
View Answer 2 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒

Assertion (A): The ac load line is different from dc load line

Reason (R): The ac load resistance seen by collector and emitter is different from dc load resistance

Both A and R are correct and R is correct explanation for A
Both A and R are correct but R is not correct explanation for A
A is correct R is wrong
A is wrong R is correct

⇒ A counter has N flip flops. The total number of states are
N
2 N
2^N
4 N

⇒ The upper end of the d.c. load line is called the __________ point and the lower end is the __________ point.
cut off, saturation
saturation, active
saturation, cut off
active saturation

⇒ The semi-conductor type 2 N 34 indicates
a n-channel MOSFET
a JFET
a diode with two electrodes
a diode with three electrodes

⇒ In PAL system weighting of R - Y and B - Y signals is done to
prevent over modulation on saturated colours
prevent under modulation of saturated colours
allow over modulation of saturated colours
allow under modulation on saturated colours

⇒ In C-language f- = 9 is equivalent to
f = -9
f = f - 9
f = 9 - 1
-f = 9

⇒ The output of a linear system for any input can be computed in which of the following ways?
Only by summation of inpulse response by convolution integral
Only by summation of step response by superposition integral
Neither a nor b
Either (a) or (b)

⇒ Consider a baseband binary PAM receiver shown below. The additive channel noise n(t) is whit with power spectral density S_N(f) = N₀/2 = 10^-20 W/Hz. The low-pass filter is ideal with unity gain and cutoff frequency 1 MHz. Let Y_k represent the random variable y(t_k10¹⁰
10⁷
1.414 x 10^-10
2 x 10^-20

⇒ In cell communication
carrier frequency change
carrier frequency constant
depend upon location
depend upon geographical area

⇒ In the circuit shown in figure, I_s = 4A, V_s = 4, the voltage V is give
6 V
8 V
4 V
2 V

⇒
Match the following:
List I (Instrument) List II (Measured quantity)
A. Hot wire 1. only voltage
B. PMMC 2. phase
C. Electrostatic 3. true RMS value
D. Lock in Amplifier 4. dc value

A-3, B-2, C-1, D-4
A-1, B-4, C-2, D-3
A-3, B-4, C-1, D-2
A-2, B-3, C-4, D-1

⇒ Triatics are
small height antenna directly mounted on jeeps, ships, etc.
the towers or masts which are used as radiators
the towers or masts which are not used as radiators
supports for antenna conductors.

⇒ The numerical value of directive gain may lie between
1 and + 1
0 and 1
0 and ∞
1 and ∞

⇒ TE₀₁ mode of propagation of electromagnetic energy
is merely the TE₁₀ mode rotated 90°
is merely the TE₁₀ mode rotated 180°
is the same as TE₁₀ mode
either (b) or (c)

⇒ Multiphase choppers are used in
low power circuits
high power circuit
both low and high power circuits
medium power circuits

⇒ If memory chip size is 256 x 1 bits, the number of chips required to make 1 k byte memory is
8
12
24
32

⇒ In 8085 microprocessor system, can an input and output port have same port address?
Yes
No
Insufficient data
None of these

⇒ In a CE bipolar transistor operating in active region, collector current is independent of
V_CE
I_B
both V_CE and I_B
none of the above

⇒ The ripple factor of a full wave rectifier is about 0.5
TRUE
FALSE

⇒ The first pulse in a TV remote control is
start pulse
preliminary pulse
either start pulse or preliminary pulse
erase pulse

⇒
Assertion (A): If Z₁(s) and Z₂(s) are positive real then Z₁(s) + Z₂(s) as well as 1/Z₁(s) and 1/Z₂(s) are positive real.
Reason (R): The poles of a positive real function are real or occur in conjugate pairs.

Both A and R are true and R is correct explanation of A
Both A and R are true and R is not the correct explanation of A
A is true but R is false
A is false but R is true

⇒
Match the following:
List I List II
A. On-off 1. steam kettle with different settings
B. Proportional 2. Elevator
C. Cascade 3. Robot-positioning
D. Digital 4. Domestic Refrigerator

A-4, B-2, C-3, D-1
A-2, B-4, C-1, D-3
A-3, B-1, C-4, D-2
A-4, B-2, C-1, D-3

⇒ The mean free path of conduction electrons in copper is about 4 x 10^-8 m. For a copper block, find the electric field which can give, on an average, 1 eV energy to a conduction electron
2.62 x 10⁷ V/m
2.64 x 10⁷ V/m
2.5 x 10⁷ V/m
2.58 x 10⁷ V/m

⇒ The state equations are in the form
X = AX + BW
X = AX + Bu
X = AX + Bx
either (a) or (b)

⇒ The term critical frequency denotes
the lowest frequency that is reflected by the ionosphere
the highest frequency that is reflected by the ionosphere at vertical distance
the lowest frequency by which communication is possible between two given points
none of the above

⇒ A class D chopper
can operate in first quadrant only
can operate in second quadrant only
can operate in either first or fourth quadrant
can operate in all the quadrants

⇒ The impulse response of the DT - LTI system is given be
1 and 2
2 and 3
1 and 3
1, 2 and 3

⇒ A stepper motor is
a two phase induction motor
is a kind of rotating amplifier
is an electromagnetic transducer used to convert an angular position of shaft into electrical signal
is an electromechanical device which actuates a train of step angular movements in response to a train of input pulses on one to one basis

⇒ The spins in a ferrimagnetic material are
all aligned parallel
partially aligned antiparallel without exactly cancelling out sublattice magnetisation
randomly oriented
all aligned antiparallel such that the sublattice cancels out exactly

⇒ In measurements using strain gauge, the dummy strain gauge is used to
compensate for resistance of strain gauge
compensate for change in temperature
compensate for error due to change in voltage of battery
compensate for error in voltmeter

	List I (Instrument)		List II (Measured quantity)
A.	Hot wire	1.	only voltage
B.	PMMC	2.	phase
C.	Electrostatic	3.	true RMS value
D.	Lock in Amplifier	4.	dc value

	List I		List II
A.	On-off	1.	steam kettle with different settings
B.	Proportional	2.	Elevator
C.	Cascade	3.	Robot-positioning
D.	Digital	4.	Domestic Refrigerator

Users Also Read
Previous Papers

Aptitude

Reasoning

Gen.Knowledge

Speak English

English / Verbal

Online / Mock Test

Vedic Math