Question is ⇒ Thermosetting polymers are, Options are ⇒ (A) injection moulded, (B) extruded, (C) cast moulded, (D) none of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ Thermosetting polymers are, Options are ⇒ (A) injection moulded, (B) extruded, (C) cast moulded, (D) none of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Thermosetting polymers are
A.	injection moulded [Wrong Answer]
B.	extruded [Wrong Answer]
C.	cast moulded [Correct Answer]
D.	none of the above [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which of the following are universal gates?

NAND
NOR
XOR

Select the correct answer from the codes given below:
1 and 2 only
1 and 3 only
2 and 3 only
1, 2 and 3

⇒ In the given figure shows a logic circuit. The minimum Boolean expression for this circui
A + B
A + B + C
AB + C
AB + AC + BC

⇒ μ₀ = 8.85 x 10^-12F/m.
TRUE
FALSE

⇒

Assertion (A): The conductivity of an n type semiconductor increases with increase in temperature and increase in density of donor atoms.

Reason (R): Diffusion of carriers occurs in semiconductors.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒

Assertion (A): The Laplace transform of a ramp is 1/s².

Reason (R): The integral of a unit step function gives an impulse function.

Both A and R are true and R is correct explanation of A
Both A and R are true and R is not the correct explanation of A
A is true but R is false
A is false but R is true

⇒ A + AB =
A
A
A + B
A + B

⇒ A network N is dual of network N if
both of them have same mesh equation
both of them have same node equation
mesh equation of one are the node equations of the other
KCL and KVL equations are the same

⇒ Ferrites are
hard materials
brittle materials
not easily machinable
materials with all above properties

⇒ A capacitor can be represented by a capacitance and resistance in parallel. For a good capacitor, this parallel resistance should be
negligible
low
high
very high

⇒ Which of the following computer memories is fastest?
Cache
Primary
Mass storage
Off line back up

⇒ PCM : Quantising Noise :: Transistor :
Partition noise
Shot noise
Whirl
No noise

⇒ A Hartley oscillator uses
a tapped inductor
a tapped capacitor
both (a) and (b)
neither (a) nor (b)

⇒ Electromagnetic waves transport
energy only
momentum only
energy as well as momentum
neither energy nor momentum

⇒ Which of the following amplifier circuit using junction transistor has the best gain?
Common base
Common emitter
Common collector
All have the same gain

⇒ If the radiated power of AM transmitter is 10 kW, the power in the carrier for modulation index of 0.6 is nearly.
8.24 kW
8.47 kW
9.26 kW
9.6 kW

⇒

Assertion (A): If an atom of polarizability a is placed in homogeneous field E, the energy stored is 0.5 aE².

Reason (R): Capacitance of an isolated conducting sphere R in vacuum is 4 p∈₀ R farads.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true

⇒ If a signal band limited for f_m is sampled at a rate less than 2 f_m the reconstructed signal will be
smaller in amplitude
distorted
having higher frequencies suppressed
none of the above

⇒ If a small amount of Cu is added to Ni conductor, then
resistivity of Ni will decrease at all temperatures because Cu is a better conductor than Ni
residual resistivity of Ni at low temperature will increase as Cu atoms act as defect centres
resistivity of Ni will increase at all temperatures as Cu destroys the periodicity of Ni and acts as defects
resistivity of Ni remains the same

⇒ If Laplace transform of f(t) is F(s), then £ f(t - a) u (t - a)= 0
e^as F(s)
e^-as F(s)
- e^as F(s)
- e ^-as F(s)

⇒ The binary addition 1 + 1 =
11
10
111
100

⇒ The circuit consisting of two transistor connected in series with the d.c. supply voltage is called
push pull
differential pair
stacked V⁺
complementary symmetry

⇒ Which binary addition is incorrect?
1101.1 + 1011.1 = 11001.0
101101 + 1101101 + 1100011
0.0011 + 0.1110 + 1.0001
1100.001 + 1011.011 = 10111.100

⇒ A loss less line of characteristic impedance Z₀ is terminated in pure reactance of -jZ₀ value. VSWR is
10
2
1
infinity

⇒ In figure, the power associated with 3 A sourc
36 W
24 W
16 W
8 W

⇒ In 8085
the upper 8 address bits appear on address bus and lower 8 bits on address data bus
the lower 8 address bits appear on address bus and the upper 8 address bits appear on address data bus
either upper or lower 8 address bits may appear at address bus
either upper or lower 8 address bits may appear at address data bus

⇒ If the secondary winding of CT is opened when primary coil is carrying current
transformer will burn immediately
there will be weak flux density in core
there will be very high induced voltage in secondary
there will be high current in secondary

⇒ For air filled circular waveguides
the attenuation due to imperfect conducting walls is negligible
the attenuation due to imperfect dielectric is negligible
both the attenuation i.e. due to imperfect conducting walls and due to imperfect dielectric are significant
the total attenuation is almost zero

⇒ A stepper motor is essentially
a synchronous motor
induction motor
dc motor
either (b) or (c)

⇒ Consider the following statements:

Internal sorting is used if the number of items to be sorted is very large.
External sorting is used if the number of items to be sorted is vary large.
External sorting needs auxiliary storage.
Internal sorting needs auxiliary storage.

Which of the above statements are correct?
1 and 2
2 and 3
3 and 4
2 and 4

⇒ The given figure shows dB magnitude plots for type 0, type 1 and type 2 systems. Out of t
curves 1, 2, 3 are for type 0, 1, 2 systems respectively
curves 1, 2, 3 are for type 2, 1, 0 systems respectively
curves 1, 2, 3 are for type 1, 0, 2 systems respectively
curves 1, 2, 3 are for type 1, 2, 0 systems respectively