Question is ⇒ Thermosetting plastic materials, Options are ⇒ (A) can be repeatedly melted., (B) is useful for melt casting., (C) can not be melted after forming., (D) is useful for spinning., (E) , Leave your comments or Download question paper.

Question is ⇒ Thermosetting plastic materials, Options are ⇒ (A) can be repeatedly melted., (B) is useful for melt casting., (C) can not be melted after forming., (D) is useful for spinning., (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Thermosetting plastic materials
A.	can be repeatedly melted. [Wrong Answer]
B.	is useful for melt casting. [Wrong Answer]
C.	can not be melted after forming. [Correct Answer]
D.	is useful for spinning. [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Synthetic rubber
deforms, if stretched to double of its original dimension.
is brittle at low temperature
is softer at higher temperature.
is highly permeable to air & water and is readily attacked by chemicals & atmospheric gases.

⇒ Flexible foam (for mattresses) are usually made of
PVC
silicone rubber
polyurethanes
polyamides

⇒ Natural rubber is obtained from latex, which is a colloidal dispersion of rubber in water. Which of the following is used as a coagulant in latex ?
Ammonium alum
Potassium alum
both a & b
neither a nor b

⇒ Polymerisation of poly functional monomers produces polymers having
good machanical strength
low viscosity
low melting point
none of these

⇒ Main constituent of cotton fibre is
lignin
cellulose
starch
gelatine

⇒ Polyvinyl chloride (PVC)
is produced by polycondensation reaction.
uses either emulsion or suspension polymerisation methods.
can be made thermosetting by adding a plasticiser.
softening temperature is 200°C.

⇒ Which of the following is not a condensation polymer ?
Bakelite
Melamine polymer
Polymethylmethacrylate (PMMA)
None of these

⇒ Condensation polymerisation of formaldehyde with __________ does not produce phenolic resin.
resorcinol
phenol
para-cresol
melamine

⇒ Elastomers are
thermosetting material.
exemplified by protein derivatives.
having high flexural strength.
having very high tensile strength and heat resistance.

⇒ Which of the following is the lowest cost plastic commercially available ?
Polythene
Teflon
Bakelite
PVC

⇒ In condensation polymerisation as compared to addition polymerisation
the monomers are unsaturated compounds.
no co-product is lost.
the monomers contain two functional groups.
generally only one monomer is involved

⇒ 90% of the caprolactum is converted to nylon-6 on its condensation polymerisation in the reactor maintained at a temperature of __________ °C.
-5
43038
250-280
500-600

⇒ Plastic articles are normally produced by __________ moulding.
green sand
injection
shell
dry sand

⇒ Phthalic anhydride is used
in making PVC
as plasticisers
in insecticides manufacture
for making nylon-6

⇒ In step growth polymerisation, generally only one type of reaction & some basic mechanism is involved. Step growth polymerisation reaction is not involved in the manufacture of
cross linked polystyrene.
phenol formaldehyde resins.
polyesters.
polyamides.

⇒ Valcunisation of rubber decreases its
tensile strength.
resistance to organic solvents.
tackiness.
working temperature range.

⇒ Viscosity of a polymer solution or melt
decreases with increase in molecular weight.
decreases with increase in temperature.
increases with increase in temperature.
does not vary with temperature rise.

⇒ Polyvinyl alcohol is used as a
cation/anion exchanger.
water soluble adhesive.
textile fibre.
non-sticky coating on frying pans.

⇒ Dacron (or terylene) fibres as compared to nylon fibres have
better heat & acid resistant properties.
poorer resistance to alkalis.
poorer dyeability.
all (a), (b) and (c).

⇒ Styrene butadiene rubber is commercially manufactured by
bulk polymerisation
suspension polymerisation
solution polymerisation
emulsion polymerisation

⇒ Which of the following polymers shows the highest anti-tacking properties ?
Melamine formaldehyde resin
Phenolic resin
Epoxy resin
Alkyd resin

⇒ Dacron is a/an
polyester
unsaturated polyester
polyamide
inorganic polymer

⇒ Zeigler - Natta catalyst (AlR₃ - AlCl₃) is used in the polymerisation of
vinyl acetate
vinyl chloride
propylene
styrene

⇒ Ion exchange resins are made of
lucite
sulphonated bakelite
polystyrene
teflon

⇒ Linear polymers are normally
thermosetting.
thermosplastic.
elastometric.
having extremely high softening point.

⇒ Buna-S is also called
polyurathane
SBR
teflon
bakelite

⇒ Which of the following polymers are produced by employing all bulk polymerisation, solution polymerisation & suspension polymerisation technique of addition (chain) polymerisation ?
PVC
Bakelite
PTFE
Epoxy resin

⇒ Liners of bags are usually made of
polythene
PVC
polypropylene
polyesters

⇒ Tyres are made by
injection moulding
extrusion
rotational moulding
compression moulding

⇒ Nitrile rubber is produced by the polymerisation of
acrylonitrile & butadiene.
acrylonitrile & styrene.
isobutylene & isoprene.
none of these.