Question is ⇒ The Vo of the op-amp circuit shown in the give, Options are ⇒ (A) 11 Vi, (B) 10 Vi, (C) Vi, (D) zero, (E) , Leave your comments or Download question paper.

Question is ⇒ The Vo of the op-amp circuit shown in the give, Options are ⇒ (A) 11 Vi, (B) 10 Vi, (C) Vi, (D) zero, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The V_o of the op-amp circuit shown in the give
A.	11 V_i [Wrong Answer]
B.	10 V_i [Wrong Answer]
C.	V_i [Wrong Answer]
D.	zero [Correct Answer]
View Answer 1 -1 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The ripple factor of a full wave rectifier is about 0.5.
TRUE
FALSE

⇒ In a solar cell, the photovoltaic voltages is the voltage at which the resultant current is
positive
zero
negative
rated current

⇒ The power in the signal s(t) = 8 cos (20 p - p/2) + 4 sin (15 pt) is
40
41
42
82

⇒ A frequency doubler has an FM signal input at 13 MHz with a deviation of 5 kHz. The output, frequency for the carrier will be
26 MHz
26.1 MHz
10 kHz
160 kHz

⇒ The characteristics of which device has peak point and valley point
SCR
PUT
SCS
Shockley diode

⇒ It has been found that in a rectifier circuit with RC filter one RC section reduces ripple by 15%. Two RC sections are used in cascade the reduction in ripple would be
0.15
0.3
1.5
2.25

⇒ The wave applied to X plates, for ohtaining trace of voltage wave, is
sawtooth wave
sinusoidal wave
rectangular wave
either (a) or (c)

⇒ The temperature at which some materials become superconductors is called
Transition temperature
Curie temperature
Neel temperature
Onnes temperature

⇒ Consider the differential amplifier shown in figure. (Assume β is very hi
1 MΩ
100 kΩ
15 kΩ
≈ 0

⇒ For an m-derived filter, attenuation is infinite when f = f_∞.
TRUE
FALSE

⇒ For a parallel two wire line with both conductors touching each other, the characteristic impedance is about
300 Ω
200 Ω
80 Ω
24 Ω

⇒ A folded dipole antenna is conveniently connected to
shielded line
two wire line
coaxial line
flat ribbon type transmission line

⇒ The op amp is used in
A/D converters
D/A converters
both (a) and (b)
shift registers

⇒

Assertion (A): In the circuit shown figure the diode is used to protect the active devices. Transistor T goes into saturation when a positive pulse is applied at base and non conducting

Reason (R): When the current in an inductor is suddenly stopped, a high voltage is induced across
Both A and R are correct and R is correct explanation for A
Both A and R are correct but R is not correct explanation for A
A is correct R is wrong
A is wrong R is correct

⇒ When an ac circuit has sources of different frequencies, the only method of analysis is superposition theorem.
TRUE
FALSE

⇒ Which of the following is not an integer constant?
0
-8
1074
-8.1

⇒

Assertion (A): The gain of an FET amplifier can be changed by changing g_m

Reason (R): Most receivers use automatic gain control to counteract changes in volume caused by fading

Both A and R are correct and R is correct explanation for A
Both A and R are correct but R is not correct explanation for A
A is correct R is wrong
A is wrong R is correct

⇒ The equivalent form of the logical expression (ABC + ABC + ABC + ABC + ABC) is:
C + (A ⊕ B)
(A + B + C)(A + B + C)
(A + B + C)(A + B + C)(A + B + C)
(A + B + C)(A + B + C)(A + B + C)

⇒

Assertion (A): The line integral of B about a closed contour, in a region containing steady current, is μ₀ times the total net current, following through the contour of integration.

Reason (R): The curl of B is equal to μ₀ times the current density vector J

Both (A) and (R) are true and (R) is the correct explanation of (A)
Both (A) and (R) are true but (R) is not the correct explanation of (A)
(A) is true but (R) is false
(A) is false but (R) is true

⇒ Maximum power from a source having internal resistance R_i is delivered to a resistive load R_L, if
R_i > R_L
R_i < R_L
R_i = R_L²
R_i = R_L

⇒

Assertion (A): A small section of high impedance line is equivalent to a series inductance.

Reason (R): A small section of a low impedance line is equivalent to a series resistance.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ The capacitance of a parallel plate capacitor varies as per the equation C(t) = C₀ (1 - cos ωt). It is connected to a battery of V volts. The equation for current is
ωC₀V (1 - cos ωt)
ωC₀V(1 - sin ωt)
ωC₀V (1 - sin 2ωt)
ωC₀V sin ωt

⇒ A voltage doubler circuit uses
two diodes
two capacitors
two diodes and two capacitors
none of the above

⇒ In the circuit of figure, the current through battery E_{34 A charging
4 A discharging
4 A charging or discharging depending on value of E₃
4 A charging or discharging depending on values of E₁, E₂, E₃}

⇒ Consider the following statements

A total of about 1 million bytes can be directly accessed by 8086 microprocessor.
The 8086 has thirteen 16 bit registers.
The 8086 has eight flags.
Compared to 8086, the 80286 provides a higher degree of memory protection.

Of the above statements
1, 2, 3, 4 are correct
1, 3, 4 are correct
1, 2, 4 are correct
1, 2, 3 are correct

⇒ Consider the following materials

Nickel
Silver
Oxygen
Aluminium

The correct sequence in the order of decreasing permeability is
1, 4, 3, 2
1, 4, 2, 3
4, 1, 3, 2
4, 1, 2, 3

⇒ The waveform shown in the given Figure can be written
v(t) = u(t - 1) + u(t - 2) + u(t - 3) + u(t -4)
v(t) = u(t - 1) + u(t - 2) + u(t - 3) + u(t -4) - u(t - 5)
v(t) = u(t - 1) + u(t - 2) + u(t - 3) + u(t -4) - 4u(t - 5)
v(t) = u(t - 1) + u(t - 2) + u(t - 3) + u(t -4) + 4u(t - 5)

⇒ In a colour TV receiver, AGC adjusts the gain of
RF stage only
IF stage only
RF stage and one or two IF stages
none of the above

⇒ In fabricating silicon BJT in ICs by the epitaxial process, the number of diffusions used is usually
2
3
4
6

⇒ In a radar system the solution to blind speed problem is to
use MTI
use monopoles
vary PRF
change Doppler frequency