Question is ⇒ The two basic types of axle are, Options are ⇒ (A) Dead and floating, (B) Dead and live, (C) Floating and semi floating, (D) , (E) , Leave your comments or Download question paper.

Question is ⇒ The two basic types of axle are, Options are ⇒ (A) Dead and floating, (B) Dead and live, (C) Floating and semi floating, (D) , (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The two basic types of axle are
A.	Dead and floating [Wrong Answer]
B.	Dead and live [Correct Answer]
C.	Floating and semi floating [Wrong Answer]
View Answer 7 -2 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The weight or pressure required to deflect a spring in mm is called the spring
Weight
Deflection
Rate
Rebound

⇒ Weight can be attached to wheel rim to correct
Wheel alignment
Wheel run out
Wheel balance

⇒ Immediately after ignition, combustion chamber temperatures may reach a value of
15000C
55000C
25000C
75000C

⇒ The slip joint permits a change in the
Length of shaft
Speed of rotation
Angle of drive

⇒ In the integral type of power brake, the diaphragm acts directly on the hydraulic piston in the
Master cylinder
Wheel cylinder
Multiplier unit

⇒ In the slip joint, slippage occurs between internally and externally mated
Couplings
joints
Splines

⇒ Whirling of the propeller shafts is mainly due to
The transmission of torsional vibration of the crankshaft
The use of a sliding joint in the propeller shaft
The use of universal joints in the drive
Lack of balance and excessive length of propeller shaft

⇒ Which motor cycle has maximum power rating
Rajdoot
Jawa
Yamaha
Bullet

⇒ Differential mechanism at the axle is provided mainly to
Enable the vehicle go round corners
Equalize the division of torque between the two wheels c. To provide a reduction ratio
To turn the drive through a right angle

⇒ The purpose of the guide ring in the fluid coupling is to reduce oil
Movement between the members
Turbulence
Level in coupling

⇒ The heat is added in the cycle at
Constant pressure
Constant volume
Approximately constant pressure and constant volume

⇒ During combustion the pressure in the cylinder may increase to as much as
50 Kg/cm2
400 Kg/cm2
10 Kg/cm2

⇒ The second movement of the gear shift lever produces
The correct gears to mesh
The movement of the drive gear
Release of clutch

⇒ The conventional motor car has
Two forward speeds
Three forward speeds
Four forward speeds

⇒ Clutch noises are usually most noticeable when the engine is
Accelerating
Decelerating
Idling
Being started

⇒ In a passenger car a typical arrangement of braking with drum brakes will be
Two leading shoes at front and leading & trailing at rear
All the wheels having leading and trailing shoes
All the wheels having two leading shoes
Front leading and trailing, rear two leading shoes

⇒ If the connecting rod longer, the side thrust of the piston is
Increased
Constant
Decreased

⇒ Parts of the clutch that should not be cleaned in solvent include the
Friction disc and throw out bearing
Friction disc cover
Throw out bearing and springs
Release levers and springs

⇒ Twisting and untwisting of the crankshaft is called
Torsional vibration
Power impulsion
Torsional balance

⇒ In a vehicle with dual rear axle, the wheel base is measured from the
Axis of the front wheel to the nearest rear wheel axis
Axis of the front wheel to the farthest rear wheel axis
Rear of cab to farthest rear wheel axis
Axis of the front wheel to an axis midway between the axes of rear wheels

⇒ In the torque converter, oil leaving the turbine is changed into a helping direction by curved
Pump vanes
Stator vanes
Turbine vanes

⇒ Connecting rods are generally of the following from
Forged round section steel
Cast steel triangular section
Forged square section steel
Forged I section steel

⇒ One advantage of using an exhaust valve as insert is that the ring
Withstands high exhaust gas temperature better
Is more easily machined
Wears in more quickly

⇒ The function of the relay valve in a compressed air brake system is to
Limit the maximum pressure reached in brake chambers
Relieve air pressure in brake chambers when it reaches a maximum value
Reduce the effort required at the brake pedal
Speed up the supply of air to brake chambers located at a distance from brake valve

⇒ As the battery is discharged, the active materials in both negative and positive plates are changed to
Spongy lead
Sulphuric acid
Lead oxide
Lead sulphate

⇒ The number of parallel paths in a lap winding of the armature of a DC generator is equal to
Half the number of poles
Number of poles
Two

⇒ The most widely used brakes are operated
Electrically
Hydraulically
By air pressure
By vacuum

⇒ IHP minus FHP equals
BHP
SAF HP
m.e.p

⇒ The purpose of the fluid coupling is to act as a
Synchronizing device
Automatic gear changer
Flexible power-transmitting coupling

⇒ A fluid coupling
Acts like flywheel and replaces it since as it is known also by the name fluid wheel
It takes the place of friction clutch and replaces it completely in synchromesh transmission systems
It replaces the friction clutch and the Gearbox also
Does the function of a clutch automatically, but cannot be used for shifting transmission to effect Gear changes