Question is ⇒ The turn on time of an SCR is 5 micro second. Its trigger pulse should have, Options are ⇒ (A) short rise time with pulse width = 2.5 μs, (B) long rise time with pulse width = 3 μs, (C) short rise time with pulse width = 4 μs, (D) long rise time with pulse width = 4 μs, (E) , Leave your comments or Download question paper.

Question is ⇒ The turn on time of an SCR is 5 micro second. Its trigger pulse should have, Options are ⇒ (A) short rise time with pulse width = 2.5 μs, (B) long rise time with pulse width = 3 μs, (C) short rise time with pulse width = 4 μs, (D) long rise time with pulse width = 4 μs, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The turn on time of an SCR is 5 micro second. Its trigger pulse should have
A.	short rise time with pulse width = 2.5 μs [Wrong Answer]
B.	long rise time with pulse width = 3 μs [Wrong Answer]
C.	short rise time with pulse width = 4 μs [Correct Answer]
D.	long rise time with pulse width = 4 μs [Wrong Answer]
View Answer 1 -4 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ If v(t) = 0 for t < 0 and e^-at for t ≥ 0 V(jω) = 1/(a + jω).
TRUE
FALSE

⇒ If the oscillator output is modulated by audio frequencies upto 10 kHz, the frequency range occupied by the side bands will be
711.9 kHz to 712.1 kHz
702 kHz to 722 kHz
692 kHz to 732 kHz
71.2 kHz to 71.20 kHz

⇒

Assertion (A): Logical group of instructions contains instructions for logic operations.

Reason (R): Data transfer group instruction is basically a copying instruction.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ The M circle for M = 1 is the
straight line at x = - 0.5
critical point (-l, jo)
circle with r = 0.33
circle with r = 0.67

⇒ Which control action is also called rate control?
Proportional
Derivative
Integral
Proportional plus integral

⇒ The phase angle curve of G(jω) H(jω) can be drawn
by adding the phase angle curves of individual factors
by subtracting the phase angle curves of individual factors
by multiplying the phase angle curves of individual factors
by dividing the phase angle curves of individual factors

⇒ 25 persons are in a room. 15 of them play hockey, 17 of them play football and 10 of them play both hockey and football. Then the number of persons playing neither hockey nor football is:
2
17
13
3

⇒ The input to a parity detector is 1001. The output is
0
1
0 or 1
indeterminate

⇒ The Hilbert transform of cos ω₁t + sin ω₂t is
sin ω₁t + cos ω₂t
sin ω₁t - cos ω₂t
cos ω₁t - cos ω₂t
- sin ω₁t + cos ω₂t

⇒ A TRIAC can be turned on :
by applying a positive signal to gate
by applying a negative signal to gate
by applying either positive or negative signal to gate
none of the above

⇒ Surface integral of the electric field intensity is
differential of volume flux
electrical charge
net flux emanating from the surface
none of the above

⇒ In thermal ohm's law, temperature and power loss are analogous to
V and I respectively of ohm's law
I and V respectively of ohm's law
R and V respectively of ohm's law
I and R respectively of ohm's law

⇒ The primary function of a clamper circuit is to
suppress variations in signal voltage
raise +ve half cycle to the signal
Lower -ve half cycle of the signal
introduce a dc level into an a.c. signal

⇒ A FET is a __________ controlled device whereas a bipolar transistor is a __________ controlled device.
gate, drain
drain, gate
current, voltage
voltage, current

⇒ An RLC series circuit is excited by 200 V, 100 Hz supply. The current is 20 A. If R = 10 Ω, X_L = 50 Ω, X_C is
10 Ω
14.14 Ω
7.07 Ω
50 Ω

⇒ Three impedances (3 + j 4) Ω each are connected in star. The impedances of equivalent delta circuit will be
3 - j 4 Ω each
9 + j 12 Ω each
9 - j 12 Ω each
3 + j 4, 3 - j 4 and 4 - j 3 Ω

⇒ The phenomenon of dielectric hysteresis occurs with
dc
ac
both ac and dc
none of the above

⇒ A 2-terminal network consists of one of the RLC elements. The elements is connected to an ac supply. The current through the element is 1 A. When an inductor is inserted in series between the source and the element, the current through the element becomes 2 A. What is this element?
A resistor
An inductor
A capacitor
Cannot be single element

⇒ If the thermal resistance of a transistor is lower it means
higher junction temperature
lower junction temperature
higher or lower junction temperature depending on circuit conditions
higher or lower junction temperature depending on transistor

⇒ If the gate of JFET is reverse biased, the width of depletion region
becomes zero
is uniform
is more near the source
is more near the drain

⇒ A 16 bit type ADC uses 1 MHz clock its maximum conversion time is __________ .
16 μs
15 ms
6.5 ms
66 ms

⇒ In figure, the switch has been in closed position for a long time. At t = 0, the switch is opened. At t = 0⁺, the current R_{10.333333333333333
0.166666666666667
0.25
0.0833333333333333}

⇒ In a CD player the speed of CD is
constant at 500 rpm
constant at 200 rpm
varies from 200 to 500 rpm
none of the above

⇒ The output data lines of microprocessor and memories are usually tristated because
more than one device can transmit information over the data bus by enabling only one device at a time
more than one device can transmit information over the data bus at the same time
the data lines can be multiplexed for both I/P and O/P
it increases the speed of data transfers over the data bus

⇒ A semiconductor diode is biased in forward direction and carrying current I. The current due to holes in p material is
I
0
less than I
0.5

⇒ The read and write cycle times of cache memory are in the range of
1 - 3 ns
25 ns - 45 ns
200 ns - 300 ns
1 μs

⇒ Ebers Moll model is applicable to
bipolar Junction transistor
N MOS transistor
unipolar junction transistor
field effect transistor

⇒ The main purpose of using transformer coupling in a class A amplifier is to make it more
efficient
less costly
less bulky
distortion free

⇒ A decade counter skips
binary states 1000 to 1111
binary states 0000 to 0011
binary states 1010 to 1111
binary states 1111 to higher

⇒ RF amplifiers are used in radio receivers for
better sensitivity
improved signal-to-noise ratio
better coupling of receiver to the antenna
all of the above