Question is ⇒ The three forward speed and the reverse transmission consists of three shafts and, Options are ⇒ (A) Three gears, (B) Five gears, (C) Eight gears, (D) Ten gears, (E) , Leave your comments or Download question paper.

Question is ⇒ The three forward speed and the reverse transmission consists of three shafts and, Options are ⇒ (A) Three gears, (B) Five gears, (C) Eight gears, (D) Ten gears, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The three forward speed and the reverse transmission consists of three shafts and
A.	Three gears [Wrong Answer]
B.	Five gears [Wrong Answer]
C.	Eight gears [Correct Answer]
D.	Ten gears [Wrong Answer]
View Answer 4 -9 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In the power assisted type of brake the bellows applies force to the master cylinder piston
Through diaphragm linkage
Directly
Through mechanical linkage

⇒ In a six cylinder engine there is balance of
Primary forces only
Secondary forces only
Both primary and secondary forces

⇒ Bleeding of brakes means
Filling the master cylinder with brake oil
Adjusting the brake shoe
Removing air between master cylinder and each wheel unit

⇒ The axle bevel gears in the differential mesh with the
Differential pinion gears
Ring gear
Drive pinion
Main gear

⇒ The synchronizing device used in the transmission uses
Cone braking surfaces
Flat braking surfaces
Synchronizing pins

⇒ In the multiplier power brake system, movement of the brake pedal
Increases the hydraulic pressure which actuates the control valve
Actuates the valve in the bellows through linkage
Actuates the valve to admit atmospheric pressure to one side of the diaphragm

⇒ Overdrive is provided in the transmission of a vehicle to
Reach higher road speeds
improved fuel consumption
achieve better acceleration
carry more load

⇒ Synchronizing devices are designed to prevent gear clash when shifting into
First and second
Second and high
First and reverse

⇒ Axle shaft of the three-quarter floating axle is subjected to
Bending stress only
Torsional stress only
Bending and torsional stress
Torsional stress and stress due to axial force during cornering

⇒ Synchronizing is designed to prevent gear clash when shifting into
First and reverse
First and second
Second and high

⇒ The ease with which a liquid changes to a vapour is called its
Vapourability
Boiling point
Viscosity
Volatility

⇒ In the Hotchkiss drive, the rear end torque is absorbed by the
Torque tube
Rear springs
Radius rods

⇒ In the differential to correct for heavy face contact on the drive gear teeth, it is necessary to move the
Drive pinion in
Drive pinion out
Drive gear out and then adjust backlash

⇒ Two types of antifreeze are
Iso octane and ethylene glycol
Alcohol base and ethylene glycol
Ethylene glycol and propylene glycol

⇒ The fluid coupling consists essentially of two
Doughnuts
Vane members
Guide rings
Driving shafts

⇒ The ring gear is adjusted in the differential by use of
Selective washers of proper thickness
Bearing adjuster
Adjusting screws

⇒ In the high gear in the transmission, main shaft turns at the same speed as the
Idler shaft
Counter shaft
Clutch shaft

⇒ The fluid coupling is most efficient as drive ratio approaching to
1:1
2:1
1:5:1
1:3

⇒ In 'V' type engines the included angle between two banks of cylinders is
450
600
1300
900

⇒ The heat is added in the cycle at
Constant pressure
Constant volume
Approximately constant pressure and constant volume

⇒ In the differential the ring gear is attached to the
Bevel gear
Drive gear
Differential case
Propeller shaft

⇒ The propeller shaft has one or more
Spur gears
Elbow joints
Universal joints
Fluid couplings

⇒ As the battery is discharged, the active materials in both negative and positive plates are changed to
Spongy lead
Sulphuric acid
Lead oxide
Lead sulphate

⇒ The weight or pressure required to deflect a spring in mm is called the spring
Weight
Deflection
Rate
Rebound

⇒ The part of the vehicle holds the passengers and the cargo to be transported is known as
Hull
Chassis
Cabin
Sedan

⇒ Conformability of an engine bearing is
Ability of a bearing to withstand the wear and tear
Resistivity to corrosion
Ability of the bearing to adjust itself to variations in shaft alignment and journal shape
Ability of a bearing to permit foreign particles to embed in it

⇒ The universal joint permits a change in the
Length of the shaft
Speed of rotation
Angle of drive

⇒ When the axle is pulled the bearing
Stays in the housing
Stays in the differential
Comes out with it

⇒ The number of planetary gear sets in a hydromatic transmission system is
Two
Three
Four
Five

⇒ If two meshing gears have 4:1 gear ratio and the smaller gear has 12 teeth, the large gear will have
12 teeth
24 teeth
36 teeth
48 teeth