Question is ⇒ The terminals of a power BJT are called, Options are ⇒ (A) emitter, base, collector, (B) emitter, base, drain, (C) source, base, drain, (D) source, base, collector, (E) , Leave your comments or Download question paper.

Question is ⇒ The terminals of a power BJT are called, Options are ⇒ (A) emitter, base, collector, (B) emitter, base, drain, (C) source, base, drain, (D) source, base, collector, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The terminals of a power BJT are called
A.	emitter, base, collector [Correct Answer]
B.	emitter, base, drain [Wrong Answer]
C.	source, base, drain [Wrong Answer]
D.	source, base, collector [Wrong Answer]
View Answer 2 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ A first order element yields almost exact duplication only for constant or slowly varying phenomenon.
TRUE
FALSE

⇒ In the circuit of figure the voltage across capacitor when switch is closed at t = &infin
0 V
20 V
very large
7.5 V

⇒ Maximum undistorted power output of a transmitter is obtained when its modulation is __________ percent.
more than 100
100
less than 100
50

⇒ In which function is each term known as maxterm?
SOP
POS
Hybrid
SOP and Hybrid

⇒ When a lead acid battery is being charged, the specific gravity of the electrolyte
decreases
increases
either increases or decreases
remains the same

⇒ A BJT amplifier has a power gain of 0.5 from source to base. The power gain in dB is
-0.3 dB
-3 dB
-6 dB
-10 dB

⇒ A 0 to 6 counter consist of 3 flip-flop and a combinational circuit of 2 input gates. The combinational circuit consist of
one AND gate
one OR gate
one AND and One OR
two AND gate

⇒ A collector collects
electrons from the base in case of N-P-N transistor
electrons from the emitter in case P-N-P transistor
holes from the base in case of N-P-N transistor
holes from the base in case of P-N-P transistor

⇒ A transistor is operated as non-saturated switch to eliminate
turn on time
turn off time
storage time
delay time

⇒ A frequency multiplier stage should operate as
class A
class AB
class C
either of the above

⇒ The input to negative clamper has a peak value of V_p. Then in the output the positive and negative peaks are nearly
0 and -2 V respectively
V_p and -V_p respectively
2 V_p and 0 respectively
none of the above

⇒ For a second order system ω_n is natural frequency, ω_d is frequency of damped oscillations and ζ is damping factor. Then
ω_d = ω_n ξ
ω_d = ω_n (1 - ξ)²
ω_d = ω_n (1 - ξ)^0.5
ω_d = ω_n (1 - ξ²)^0.5

⇒ Automatic sensitivity control by target voltage control is easily possible in
Vidicon
Plumbicon
New vicon
both (b) and (c)

⇒ In case of a transistor amplifier the emitter resistance R_e is removed
the gain of the amplifier will reduce
heat sink will not be required
Q-point will become unstable
base to emitter function will be less forward biased

⇒ An electrostatic voltmeter is suitable for
low voltage at high frequency
high voltage
low voltage at low frequency
all ac and dc voltages

⇒ In figure, Z_a = 100∠50°, Z_b = 300∠-90° and Z_c = 200∠0°. For balanced condition, Z_d will
600∠ - 40°
600∠140°
600∠ - 140°
150∠140°

⇒ The properties of FETs closely resemble those of a
thermionic valve
P-N-P transistor
N-P-N transistor
UJT

⇒ Which of the following statements is non-executable in FORTRAN 77?
DO
ASSIGN
END
DIMENSION

⇒ The energy to cause thermionic emission is supplied by heating the cathode.
TRUE
FALSE

⇒ It is desired that transmission line and load should match for a range of frequencies. The best method is
to use a balun
to use a single stub of adjustable position
to use a double stub
to use a broad band amplifier

⇒ The elements which become superconducting at extremely low temperatures are
good conductors at room temperature
ferromagnetic at room temperature
relatively poor conductors at room temperature
insulators at room temperature

⇒

Assertion (A): In a BCD to 7 segment decoder the number of outputs active at one time is always the same.

Reason (R): A decoder can be used to interface BCD input to LED display.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ Nyquist plot provides information about absolute stability as well as relative stability.
TRUE
FALSE

⇒ The currents fed to the two dipoles of turnstile antenna are
in phase
in quadrature
in phase opposition
either (a) or (c)

⇒ The direction in a Yagi Uda antenna
is longer than the radiating element
is shorter than the radiating element
can be longer or shorter than the radiating element
does not exist

⇒ In the given figure the reflected current wave after first reflectio
0.18 A
-0.18 A
0.3 A
-0.3 A

⇒ High speed counter
ring counter
ripple counter
synchronous counter
asynchronous counter

⇒ An 8-bit microprocessor has 16 bit address bus A₀ - A₁₅. The processor addresses a 1-K byte memory chip as shown. The address range for the chi
(F00F)_H TO (F40E)_H
(F000)_H TO (F3FF)_H
(F100)_H TO (F4FF)_H
(F700)_H TO (FAFF)_H

⇒ Consider the following statements

The effect of feedback is to reduce system error
Feedback increases the system gain at one frequency but reduces the system gain as another frequency
Feedback can cause an originally stable system to become unstable

Which of the above statements are correct?
1, 2, 3
1, 2
2, 3
1, 3

⇒ Decimal number 10 is equal to binary number
1110
1010
1001
1000