Question is ⇒ The starting resistance of a D.C. motor is generally, Options are ⇒ (A) low, (B) around 500 ohms, (C) 1000 ohms, (D) infinitely large, (E) , Leave your comments or Download question paper.

Question is ⇒ The starting resistance of a D.C. motor is generally, Options are ⇒ (A) low, (B) around 500 ohms, (C) 1000 ohms, (D) infinitely large, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The starting resistance of a D.C. motor is generally
A.	low [Correct Answer]
B.	around 500 ohms [Wrong Answer]
C.	1000 ohms [Wrong Answer]
D.	infinitely large [Wrong Answer]
View Answer 10 -4 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In an overloaded motor main danger arises due to
winding getting overheated
busbars getting heated
starter getting damaged
bearings getting overheated

⇒ In the D.C. motor the iron losses occur in
the field
the armature
the brushes
the commutator

⇒ Which of the following load normally needs starting torque more than the rated torque?
Blowers
Conveyors
Air compressors
Centrifugal pumps

⇒ D.C. generators are installed near the load centres to reduce
iron losses
line losses
sparking
corona losses

⇒ In a D.C. motor constant torque is produced due to
rotor laminations
end-plates
pole shoes
commutator

⇒ Between Field's test and Hopkinson's test the main common thing is that both
use negligible power
are regenerative tests
need two similar mechanicallycoupled motors
need two electrically coupled series motors

⇒ For which application a D.C. motor is preferred over an A.C. motor ?
High speed operation
Low speed operation
Fixed speed operation
Variable speed operation

⇒ The mechanical power developed by a D.C. motor is equal to
power input + losses
back e.m.f. X armature current
power output X losses
power output X efficiency

⇒ Which method of braking is generally used in elevators ?
Plugging
Regenerative braking
Rheostatic braking
None of the above

⇒ Which of the following losses are significantly reduced by laminating the core of a D.C. generator ?
Hysteresis losses
Eddy current losses
Copper losses
Windage losses

⇒ In D.C. motor which of the following can sustain the maximum temperature rise?
Slip rings
Commutator
Field winding
Armature winding

⇒ Which D.C. motor will be preferred for machine tools ?
Series motor
Shunt motor
Cumulative compound motor
Differential compound motor

⇒ In a D.C. series motor, if the armature current is reduced by 50%, the torque of the motor will be equal to
100% of the previous value
50% of the previous value
25% of the previous value
10% of the previous value

⇒ If conditions for maximum power for a D.C. motor are established, the efficiency of the motor will be
less than 50%
60 to 70%
80 to 90%
1

⇒ What will happen if the back e.m.f. of a D.C. motor vanishes suddenly?
The motor will stop
The motor will continue to run
The armature may burn
The motor will run noisy

⇒ At the instant of starting when a D.C. motor is put on supply, it behaves like
a highly resistive circuit
a low resistance circuit
a capacitive circuit
none of the above

⇒ Speed control by the variation of flux, in a D.C. shunt motor, will give
constant torque drive
variable torque drive
constant power drive
variable power drive

⇒ Sparking at the commutator of a D.C. motor may result in
damage to commutator segments
damage to commutator insulation
increased power consumption
all of the above

⇒ Hopkinson's test on D.C. machines is conducted at
no-load
part load
full-load
overload

⇒ Ward-Leonard system of speed control is not recommended for
very low speeds
frequent motor reversals
wide speed range
constant speed operation

⇒ Which of the following tests will be suitable for testing two similar D.C. series motors of large capacity ?
Swinburne's test
Hopkinson's test
Field test
Brake test

⇒ Which of the following motors have almost constant speed over their full load range ?
A.C. series motors
D.C. series motors
D.C. shunt motors
Low resistance squirrel cage motors

⇒ If Ia be the armature current, then speed of a D.C. shunt motor is
independent of la
proportional to Ia
varies as (la)²
varies as¹/_{I_a}

⇒ To get the speed of D.C. motor below the normal without wastage of electrical energy ____ is used.
Ward Leonard control
rheostatic control
any of the above method
none of the above method

⇒ Which of the following motor has high starting torque ?
Synchronous motor
A.C. series motor
D.C. series motor
Induction motor

⇒ The variable resistor shunting the field of a D.C. series motor is called a
armature divertor
voltage regulator
field divertor
potential divider

⇒ Which loss in a D.C. generator varies with load ?
Copper loss
Eddy current loss
Hysteresis loss
Windage loss

⇒ The maximum end-play of a motor is about
10 mm
6 mm
2 mm
0.4 mm

⇒ Which motor should not be started on no-load ?
Series motor
Shunt motor
Cumulatively compounded motor
Differentially compounded motor

⇒ A motor for punching machine is usually subjected to
no load
continuous part load
continuous full load
intermittent load