Question is ⇒ The slope of the obstruction clearance line from the boundary of the heliport should be, Options are ⇒ (A) 1:2, (B) 1:5, (C) 1:8, (D) 1:40, (E) , Leave your comments or Download question paper.

Question is ⇒ The slope of the obstruction clearance line from the boundary of the heliport should be, Options are ⇒ (A) 1:2, (B) 1:5, (C) 1:8, (D) 1:40, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The slope of the obstruction clearance line from the boundary of the heliport should be
A.	1:2 [Wrong Answer]
B.	1:5 [Wrong Answer]
C.	1:8 [Correct Answer]
D.	1:40 [Wrong Answer]
View Answer 18 -6 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The slope of the transitional surface for A, B and C type of runway shall be
1:5
1:7
1:10
1:12

⇒ According to ICAO, all markings on the runways are
Yellow
White
Black
Red

⇒ The cruising speed of the aircraft is 500 kmph. If there is a head wind of 50 kmph, then the air speed and ground speed of the aircraft respectively will be
450 kmph and 500 kmph
500 kmph and 450 kmph
450 kmph and 450 kmph
500 kmph and 500 kmph

⇒ In approach areas of runways equipped with instrumental landing facilities any object within 4.5 km distance from runway end shall be considered as an obstruction if its height is more than
20 m
30 m
45 m
51 m

⇒ Runway threshold is indicated by a series of parallel lines starting from a distance of
3 m from runway end
6 m from runway end
10 m from runway end
15m from runway end

⇒ As per ICAO, for airports serving big aircrafts, the crosswind component should not exceed
15 kmph
25 kmph
35 kmph
45 kmph

⇒ The runway length after correcting for elevation and temperature is 2845 m. If the effective gradient on runway is 0.5 percent then the revised runway length will be
2845 m
2910 m
3030 m
3130m

⇒ Castor angle is defined as the angle
formed by the longitudinal axis of the aircraft and the direction of movement of the nose gear
between the direction of wind and the longitudinal axis of the runway
between the true speed of the aircraft and the crosswind component
between the horizontal and the fuselage axis

⇒ As per ICAO, the minimum basic runway length for A and E type of airport will be
1500 m and 600 m
2100 m and 750 m
1500 m and 750 m
2100 m and 600 m

⇒ In an airport, if 4 groups of 5 gates each located well-separated are considered for traffic and the future to present traffic ratio is 3, then the total requirement of future gates will be
32
36
44
68

⇒ For determining the basic runway.length, the landing case requires that aircraft should come to a stop within p % of the landing distance. The value of p is
40 %
50%
60%
75%

⇒ Maximum gross take-off weight of an aircraft is
equal to the maximum structural landing weight
less than the maximum structural landing weight
more than the maximum structural landing weight
equal to the empty operating weight plus the payload

⇒ The length of clear zone for none instrument runway of a small aircraft is
150 m
300 m
600 m
750 m

⇒ The main disadvantage of angle nose out parking configuration of aircraft is that the
aircraft rear loading door is far away from terminal building.
hot blast is directed towards the terminal building
overall apron area required is more
all the above

⇒ The engine failure case for determining the basic runway length may require
only clearway
only stop way ,
either a clearway or a stopway
either a clearway or a stopway or both

⇒ Which of the following is an example of failure in flexible pavements ?
Alligator cracking
Mud pumping
Warping cracks
Shrinkage cracks

⇒ Geometric design of holding apron Of these statements
1 and 2 are correct
2 and 3 are correct
1 and 3 are correct
1 alone is correct

⇒ The size of landing area for multiengined helicopters operating under 1FR conditions is
22.5 m x 22.5 m
30 m x 30 m
22.5 m x 30 m
60 mx 120 m

⇒ The capacity of parallel runway pattern depends upon
weather conditions and navigational aids available
lateral spacing between two runways and weather conditions
lateral spacing between two runways and navigational aids available
lateral spacing between two runways, weather conditions and navigational aids available.

⇒ Calm period is the percentage of time during which wind intensity is less than
4.8 kmph
6.4 kmph
8.0 kmph
9.6 kmph

⇒ In Intrumental landing system, the middle markers are located
along the extended centre line of runway end
about 1 km. ahead of the runway threshold
at the runway threshold
about 7 km. ahead of the runway threshold

⇒ As per ICAO recommendation, minimum width of safety area for instrumental runway should be
78 m
150 m
300 m
450 m

⇒ For supersonic transport aircraft, the minimum turning radius of taxiway is
60 m
120 m
180 m
240 m

⇒ The minimum width of clearway is
50 m
100 m
150 m
250 m

⇒ The slope of the obstruction clearance line from the boundary of the heliport should be
1:2
1:5
1:8
1:40

⇒ As per ICAO, for A, B, and C type of airports, maximum effective, transverse and longitudinal grades in percentage respectively are
1.0, 1.5 and 1.5
1.0, 1.5 and 2.0
1.5, 1.5 and 2.0
2.0, 2.0 and 2.0

⇒ The total length of a runway is 1000 m. The elevation at distance 0,200 m, 400 m, 600 m, 800 m and 1000 m are 100.0 m, 99.2 m, 101.0 m, 101.8 m, 101.4 m and 101.0 m respectively. The effective gradient of runway will be.
0.10%
0.26%
0.43 %
0.65%

⇒ An airport has 4 gates. If the weighted average gate occupancy time is 30 minutes and gate utilisation factor is 0.5, then the capacity of the gate will be
1 aircraft per hour
2 aircrafts per hour
4 aircrafts per hour
16 aircrafts per hour

⇒ As per ICAO recommendation, the rate of change of longitudinal gradient per 30 m length of vertical curve for A and B type of airports is limited to a maximum of
0.1 %
0.2%
0.3 %
0.4%

⇒ Zero fuel weight of an aircraft is:
equal to empty operating weight
equal to maximum landing weight
less than empty operating weight
equal to sum of empty operating weight and the maximum pay load.