Question is ⇒ The slope correction for a length of 30 m along a gradient of 1 in 20, is, Options are ⇒ (A) 3.75 cm, (B) 0.375 cm, (C) 37.5 cm, (D) 2.75 cm., (E) , Leave your comments or Download question paper.

Question is ⇒ The slope correction for a length of 30 m along a gradient of 1 in 20, is, Options are ⇒ (A) 3.75 cm, (B) 0.375 cm, (C) 37.5 cm, (D) 2.75 cm., (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The slope correction for a length of 30 m along a gradient of 1 in 20, is
A.	3.75 cm [Correct Answer]
B.	0.375 cm [Wrong Answer]
C.	37.5 cm [Wrong Answer]
D.	2.75 cm. [Wrong Answer]
View Answer 27 -15 Explanation:- Answer : A Discuss it below : Amjad Ali Said on 2020-02-15 17:12:25 1 in 20 mean that 1 rise for 20m distance then for 30m distance rise will be 1.5m So h²/2l=1.5²/2×30=3.75cm !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The slope correction for a 3° slope for a length of 100 m, is.
-0.11 m
-0.11 m
-1.87 m
-0.137 m

⇒ The curvature of the earth's surface is taken into account only if the extent of survey is more than
80 sq. km
500 sq. km
260 sq. km
1500 sq. km

⇒ Number of links per metre length of a chain are.
2
5
8
10

⇒ If the declination of the needle is 10° W.
each of the whole circle reckoning has to be micros by 10Â°
in the quadrantal method, the correction is positive in the 1st and 3rd quadrants
in the quadrantal method, the corrections is negative in 2nd and 4th quadrants
all the above.

⇒ A bearing of a line is also known as.
magnetic bearing
true bearing
azimuth
reduced bearing

⇒ The radius of a simple circular curve is 300 m and length of its specified chord is 30 m. The degree of the curve is.
5.73Â°
5.37Â°
3.57Â°
3.75Â°.

⇒ Pick up the correct statement from the following :
A level surface is perpendicular at all points to the direction of gravity
A level line lies in level surface
A horizontal surface is normal to the direction of gravity at only one point
All the above.

⇒ Check lines (or proof lines) in Chain Surveying, are essentially required.
to plot the chain lines
to plot the offsets
to indicate the accuracy of the survey work
to increase the out-turn

⇒ An obstacle which obstructs chaining but not ranging may be a
Building
Lake
Hillock
Electric pole

⇒ If a linear traverse follows a sharp curve round a large lake where it is difficult to have long legs, the accuracy of the traverse may be improved by.
taking short legs
making repeated observations of angular and linear measurements
making a subsidiary traverse to determine the length of a long leg
all the above.

⇒ In reciprocal levelling, the error which is not completely eliminated, is due to.
earth's curvature
non-adjustment of line of collimation
refraction
non-adjustment of the bubble tube.

⇒ The boundary of water of a still lake, represents.
level surface
horizontal surface
contour line
a concave surface.

⇒ The working edge of an alidade is known as
Ebonite edge
Fiducial edge
Straight edge
Graduated edge

⇒ The accuracy of measurement in chain surveying, does not depend upon.
length of the offset
scale of the plotting
importance of the features
general layout of the chain lines.

⇒ Reduced bearing of a line is an angle between.
north line and given line measured clockwise
north line and given line measured anticlockwise
east or west and the given line
given line and the part of the meridian whether N end or S end, lying adjacent to it

⇒ Keeping the instrument height as 1.5 m, length of staff 4 m, the up gradient of the ground 1 in 10, the sight on the up slope must be less than
25 cm
20 m
45 m
10 m

⇒ Mistakes which may produce a very serious effect upon the final results arise due to.
in attention
in experience
carelessness
all of these.

⇒ In a lemniscate curve the ratio of the angle between the tangent at the end of the polar ray and the straight, and the angle between the polar ray and the straight, is.
2
3
4
3/2

⇒ The angle of intersection of the two plane mirrors of an optical square is
30°
45°
60°
90°

⇒ For orientation of a plane table with three points A, B and C, Bessel's drill is.
Align b through a and draw a ray towards c, align a through b and draw a ray towards c, finally align c through the point of intersection of the previously drawn rays
Align c through a and draw a ray towards b, align a through c and draw a ray towards b, finally align b through the point of intersection of the previously drawn rays
Align c through b and draw a ray towards a, align b through c and draw a ray towards a, finally align a, through the point of intersection of the previously, drawn rays
In the first two steps any two of the points may be used and a ray drawn towards the third point, which is sighted through the point of intersection of previously drawn rays in the final step.

⇒ A discrepancy is the difference between
True value and error
Measured value and actual value
Two measured values of the same quantity
None of the above

⇒ If L is in kilometres, the curvature correction is.
58.2 L2 mm
64.8 L2 mm
74.8 L2 mm
78.4 L2 mm.

⇒ Metric chains are generally available in.
10 m and 20 m length
15 m and 20 m length
20 m and 30 m length
25 m and 100 m length

⇒ While working on a plane table, the correct rule is :
Draw continuous lines from all instrument stations
Draw short rays sufficient to contain the points sought
Intersection should be obtained by actually drawing second rays
Take maximum number of sights as possible from each station to distant objects.

⇒ A prismatic compass is used to determine
Dip at a place
Declination of a line
Whole circle bearing of a line
Quadrande bearing of a line

⇒ While measuring with a metallic tape of 30 m length pull should be applied.
1 kg
2 kg
3 kg
4 kg

⇒ The main plate of a transit is divided into 1080 equal divisions. 60 divisions of the vernier coincide exactly with 59 divisions of the main plate. The transit can read angles accurate upto.
5"
10"
15"
20"

⇒ The angle between two plane mirrors of an optical square should be
30°
45°
60°
90°

⇒ The accuracy of fix obtained by solving a two point problem is
Good
Fairly accurate
Not reliable
None of these

⇒ Three point problem can be solved by
Tracing paper method
Bessels method
Lehman's method
all of the above