Question is ⇒ The scaling factor of an MOS device using constant voltage scaling model, the gate area of the device will be scaled as, Options are ⇒ (A) 1/a, (B) 1/a2, (C) 1/a3, (D) 1/a4, (E) , Leave your comments or Download question paper.

Question is ⇒ The scaling factor of an MOS device using constant voltage scaling model, the gate area of the device will be scaled as, Options are ⇒ (A) 1/a, (B) 1/a2, (C) 1/a3, (D) 1/a4, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The scaling factor of an MOS device using constant voltage scaling model, the gate area of the device will be scaled as
A.	1/a [Wrong Answer]
B.	1/a² [Wrong Answer]
C.	1/a³ [Wrong Answer]
D.	1/a⁴ [Correct Answer]
View Answer 1 -2 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The zeros of a minimum phase function lie on
imaginary axis
left half plane or origin
left half plane or imaginary axis
right half plane or origin

⇒ A unit step function is used to represent the closing a switch in a constant voltage system.
TRUE
FALSE

⇒ Maximum undistorted power output of a transmitter is obtained when its modulation is __________ percent.
more than 100
100
less than 100
50

⇒ In CE amplifier the base current is very high.
TRUE
FALSE

⇒ A series RLC circuit is at resonance at 200 Hz. If capacitance is increased to four times, the circuit will be in resonance at
200 Hz
400 Hz
100 Hz
800 Hz

⇒ The Hilbert transform of cos ω₁t + sin ω₂t is
sin ω₁t + cos ω₂t
sin ω₁t - cos ω₂t
cos ω₁t - cos ω₂t
sin ω₁t + sin ω₂t

⇒ A lead compensator
speeds up the transient response
increases the stability margin
increases the stability margin and speeds up the transient-response.
none of the above.

⇒ One of a loss-less transmission line having the characteristic impedance of 75 Ω and length of 1cm is short-circuit. At 3 GHz, the input impedance at the other end of the transmission line is
0
resistive
capacitance
inductive

⇒ A hexadecimal odometer displays F52F. The next reading will be
E 52 F
E 52 E
E 53 F
F 53 O

⇒ In the circuit of figure, the current through battery E_{34 A charging
4 A discharging
4 A charging or discharging depending on value of E₃
4 A charging or discharging depending on values of E₁, E₂, E₃}

⇒ In figure the open circuit em
15 V
1.45 V
1.475 V
1.485 V

⇒

Assertion (A): Acceptor extrinsic semiconductor has higher conductivity than intrinsic semiconductor.

Reason (R): Addition of p-type impurity produces an allowable discrete energy level just above valence band.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true

⇒ At FM demodulator output noise power density
increases with frequency
decreases with frequency
remains unaltered
none of the above

⇒ Z₀ = (Z_oc Z_sc)^0.5
TRUE
FALSE

⇒ When analysing two port networks in cascade, it is more convenient to use
z parameters
h parameters
T parameters
y parameters

⇒ If the oscillator output is modulated by audio frequencies upto 10 kHz, the frequency range occupied by the side bands will be
711.9 kHz to 712.1 kHz
702 kHz to 722 kHz
692 kHz to 732 kHz
71.2 kHz to 71.20 kHz

⇒ A 4 bit counter with four flip-flops will count upto decimal
8
15
31
63

⇒ A resistor R of 1 Ω and two inductor L₁ and L₂ of inductances 1 H and 2 H respectively, are connected in parallel. At some time, the current through L₁ and L₂ are 1 A and 2 A, respectively. The current through R at time t = ∞ will be
zero
0.0416666666666667
0.0833333333333333
0.125

⇒ The addition of n type impurity to intrinsic material creates allowable energy levels.
slightly below conduction band
slightly above conduction band
slightly below valence band
slightly above valence band

⇒ Which one is a linear system?
y[n] = x[n] x x[n - 1]
y[n] = x[n] + x[n - 10]
y[n] = x²[n]
(a) and (c)

⇒ In a bipolar junction transistor the base region is made very thin so that
recombination in base region is minimum
electric field gradient in base is high
base can be easily fabricated
base can be easily biased

⇒ Which of the following polynomials is not Hurwitz?
P₁ = s⁸ + 2s⁶ + 4s⁴
P₂ = s⁶ - 3s⁴ + 2s² + 1
P₃ = s⁴ + 3s³ + 3s² + 2s + 1
P₄ = s⁷ + 2s⁶ 2s⁴ + 4s³ + 8s² + 8s + 4

⇒ The hexadecimal number system is
widely used in analyzing and programming microprocessors
an obsolete system no more in use
used in calculators only
none of the above

⇒ Each frequency in the modulating wave gives rise to four side bands.
TRUE
FALSE

⇒ The most commonly used moving iron instruments are
repulsion type
attraction type
a combination of attraction and repulsion type
none of the above

⇒

Assertion (A): When the forward gain of a system is increased, the transient response becomes oscillatory.

Reason (R): Increasing the forward gain reduces steady state error.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒

Match the following:

	List I		List II
A.	Multiplexer	1.	Sequential memory
B.	De-multiplexer	2.	Converts decimal number to binary
C.	Shift register	3.	Data selector
D.	Encoder	4.	Routes single input to many outputs

A-3, B-4, C-1, D-2
A-4, B-3, C-1, D-2
A-3, B-4, C-2, D-1
A-1, B-2, C-3, D-4

⇒ Microwave signals follow the curvature of the earth and the phenomenon is known as
tropospheric scatter
duct propagation
Faraday effect
none of the above

⇒

Assertion (A): When light falls at junction of p-n photodiode, its p side becomes positive and n side becomes negative.

Reason (R): When a photodiode is short circuited, the current in the external circuit flows from p side to n side.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ Which of the following is true?
A silicon wafer heavily doped boron is a p⁺ substrate
A silicon wafer lightly doped boron is a p⁺ substrate
A silicon wafer heavily doped arsenic is a p⁺ substrate
A silicon wafer lightly doped arsenic is a p⁺ substrate