Question is ⇒ The rear end suspension arrangement in which rear end torque is absorbed by the spring is called the, Options are ⇒ (A) Torque tube drive, (B) Hooks drive, (C) Differential drive, (D) Hotchkiss drive, (E) , Leave your comments or Download question paper.

Question is ⇒ The rear end suspension arrangement in which rear end torque is absorbed by the spring is called the, Options are ⇒ (A) Torque tube drive, (B) Hooks drive, (C) Differential drive, (D) Hotchkiss drive, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The rear end suspension arrangement in which rear end torque is absorbed by the spring is called the
A.	Torque tube drive [Wrong Answer]
B.	Hooks drive [Wrong Answer]
C.	Differential drive [Wrong Answer]
D.	Hotchkiss drive [Correct Answer]
View Answer 7 -3 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ If the connecting rod longer, the side thrust of the piston is
Increased
Constant
Decreased

⇒ The compression pressure in diesel engine is around
30 Kg/cm2
10 Kg/cm2
20 Kg/cm2
40 Kg/cm2

⇒ Of the four tyres on a car, the one that wears most is the
Right front tyre
Right rear tyre
Left front tyre
Left rear tyre

⇒ The function of a torque converter or fluid converter is similar to that of a
Gear box
Clutch
Shock absorber
Torsion box

⇒ The propeller shaft has one or more
Spur gears
Elbow joints
Universal joints
Fluid couplings

⇒ In a vacuum suspended unit, when the brakes are on, the piston or diaphragm has on both sides of it
Atmospheric pressure
Vacuum
Hydraulic pressure

⇒ During braking the brake shoe is moved outward to press against the
Wheel piston or cylinder
Brake lining
Brake drum or disc
Wheel rim or axle

⇒ In transmission reduction of speed is always used to obtain
Reduction of torque
Constant torque to drive the wheels
Increase of torque

⇒ An automatic transmission works on the principle of
Centrifugal device making up changes proportional to road speed
Centrifugal device connected to crankshaft making up changes prop. to engine speed
Makes changes depending on throttle position in conjunction with road speed governor
Makes gear changes at equal intervals or set road speeds

⇒ For diesel engines the nominal compression ratio is from
17 to 21:1
7.5 to 8.5:1
30 to 40:1
1 to 5:1

⇒ On a straight road, the ring gear
Rotates at the same speed as wheels
Rotates faster than wheels
Rotates slower than wheels
Does not rotate

⇒ When the direct acting shock absorber is compressed or telescoped fluid passes through the piston orifices into the upper part of the cylinder and also
Into the dust shield
Out of the dust shield
Into the reservoir
Out of the reservoir

⇒ As the load on the vehicle increase it demands
Increased braking torque
Decreased braking torque
Same braking torque

⇒ The power developed inside the engine cylinder is called
IHP
FHP
BHP

⇒ The ring gear is adjusted in the differential by use of
Selective washers of proper thickness
Bearing adjuster
Adjusting screws

⇒ The radiator tubes are manufactured by using
Cast iron tubes
Aluminum tubes
Brass tubes
Steel tubes

⇒ When preparing electrolyte, it is important to remember that
Acid and water should be poured together
Water should be poured into acid
Acid should be poured into water

⇒ To prevent distortion on re-installation on the clutch cover attaching bolts should be tightened
One at a time
Evenly
Until springs begin to compress
Until springs are expanded

⇒ In jeeps we use
Mechanical brakes
Hydraulic brakes
Air brakes

⇒ In general the design of the current regulator is such that its main actuating winding carries full
Generator voltage
Generator output
Field current
Battery voltage

⇒ In the differential, the ring gear is bolted to the
Differential housing
Differential case
Drive pinion
Axle shaft

⇒ The distance between adjacent meshing teeth of mating gears is called
Clearance
Back lash
Flank

⇒ Which of the following layouts is not used in motor vehicles?
Front engine front drive
Front engine rear drive
Rear engine front drive
Rear engine rear drive

⇒ The number of planetary gear sets in a hydromatic transmission system is
Two
Three
Four
Five

⇒ The substance added to the oil which helps to keep the engine clean is called
Grease
Thickening agent
Soap
Detergent

⇒ Clutch noises are usually most noticeable when the engine is
Accelerating
Decelerating
Idling
Being started

⇒ The ratio between the power output of an engine and the energy in the fuel burned to produce that power is called
Volumetric efficiency
Thermal efficiency
Mechanical efficiency

⇒ If two meshing gears have 4:1 gear ratio and the smaller gear has 12 teeth, the large gear will have
12 teeth
24 teeth
36 teeth
48 teeth

⇒ The ratio of the cylinder volume at BDC and the clearance volume is called
Clearance ratio
Volumetric ratio
Compression ratio

⇒ The type of braking system referred to as power brake, makes use of
Electromagnets
Compressed air
Vacuum