Question is ⇒ The ratio of tangential component of electric field at the surface of a conductor and the linear current density resulting from this field is __________ impedance, Options are ⇒ (A) characteristic, (B) critical, (C) surface, (D) polarizing, (E) , Leave your comments or Download question paper.

Question is ⇒ The ratio of tangential component of electric field at the surface of a conductor and the linear current density resulting from this field is __________ impedance, Options are ⇒ (A) characteristic, (B) critical, (C) surface, (D) polarizing, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The ratio of tangential component of electric field at the surface of a conductor and the linear current density resulting from this field is __________ impedance
A.	characteristic [Wrong Answer]
B.	critical [Wrong Answer]
C.	surface [Correct Answer]
D.	polarizing [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which of the following is used as detector in audio frequency ac bridges?
AC voltmeter
CRO
Head phones
Vibration galvanometer

⇒ The modulating frequency in frequency modulation is increased from 10 kHz to 30 kHz. The bandwidth is increased by
6
1/6 times
increase by 30 kHz
increase by 20 kHz

⇒

Assertion (A): It is not desirable to drive a transistor into hard saturation in high speed switching circuits.

Reason (R): It may not be possible to bring it back to cutoff state, if it is driven into hard saturation.

Both A and R are individually true and R is the correct explanation of A
Both A and R are individually true but R is not the correct explanation of A
A is true but R is false
A is false but R is true

⇒ Which of the following is not an integer constant?
2.3
156231
10
-256

⇒ System bus is the communication channel between microprocessor and peripherals.
TRUE
FALSE

⇒ If load impedance Z_L >> Z₀, then
Z₀ = Z_L (VSWR)
Z_L = Z₀ (VSWR)
Z_L = Z₀ (VSWR - 1)
Z_L = Z₀ VSWR

⇒ The value of the inductance of coil in which a current increases linearly from zero to 0.1A in 0.2 second producing a voltage of 5 volts is __________ .
2.5
5
10
20

⇒ Consider the following reasons for using antenna coupler

To prevent illegal radiation of spurious frequencies
To tune out reactive components of antenna impedance
To have correct value of load impedance for transmitter.

Which of the above are correct?
1, 2, 3
1, 2
1 only
2, 3

⇒ A steel bar needs 1200 AT to magnetise it. The voltage that must be applied to the magnetising coil of 100 turns and 10 Ω resistance is __________ volt.
120
12
1200
10

⇒ When the i-v curve of a photodiode passes through origin the illumination is
maximum
minimum
zero
equal to rated value

⇒ A flip-flop circuit is
monostable
bistable
multistable
unstable

⇒ Limiter is not essential in the following detector
foster-Seeley
ratio detector
balanced
none of the above

⇒ The inductance of a coil can be increased by
choosing core material having high relative permeability
decreasing diameter of the former
decreasing the number of turns
increasing core length

⇒ In which one of the following types of analog to digital convertors the conversion time is practically independent of the amplitude of the analog signal?
The dual slope integrating type
Successive approximation type
Counter ramp type
Tracking type

⇒ In Pascal the repeat and while loops will terminate
only when the logical expression controlling the loop becomes true for both repeat and while loops
only when the logical expression controlling the loop becomes false for both repeat and while loops
only when the logical expression controlling the loop becomes true for repeat loop and false for while loop
only when the logical expression controlling the loop becomes false for repeat loop and true for while loop

⇒

Match the following:

	List I (Modes)		List II (Characteristic)
A.	Evanescent	1.	Rectangular waveguide does not support
B.	Dominant mode	2.	No wave propagation
C.	TM₁₀ and TM₀₁	3.	Lowest cut-off frequency

A-1, B-2, C-3
A-2, B-3, C-1
A-1, B-3, C-2
A-2, B-1, C-3

⇒ Two rectangular waveforms of duration t₁ and t₂ seconds are convolved. What is the shape of the resulting waveform?
Triangular
Rectangular
Trapezoidal
Semi-circular

⇒ If sampling is done at the rate of 10 kHz. The bandwidth required is
35 kHz
70 kHz
10 kHz
1280 kHz

⇒ Distances near the skip distance should be used for sky-wave propagation
to avoid the Faraday effect
to avoid tilting
to prevent sky-wave and upper ray interference
so as to exceed the critical frequency

⇒ In figure, the voltmeter is ideal. The transformer has two identical windings with perfect coupling. The reading of voltmete
440 V
220 V
110 V
zero

⇒ A voltage V(t) which is a Gaussian ergodic random process with a mean of zero and a variance of 4 volt² is measured by a true rms meter. The reading will be
0
4
2
16

⇒ If a two port network is represented by an equivalent T network the admittance of series arm in term of ABCD parameter is equal to
C
1/C
(A - 1)/B
1/B

⇒ Decimal 17 in octal system is represented by
888
111
21
27

⇒ In a CD the sampling frequency is nearly
half the highest frequency in audio signal
equal to highest frequency in audio signal
double the highest frequency in audio signal
four times the highest frequency in audio signal

⇒ For pole-zero plot shown, the system is ________
minimum phase
maximum phase
mixed phase
none of these

⇒ In the given figure shows the equivalent circuit of a magic tee. If all ports are mat
n_E = n_H = 2
n_E = n_H = 0.707
n_E = 2, n_H = 0.707
n_H = 0.707, n_H = 2

⇒

Assertion (A): Class A and Class B amplifier predominate in audio applications.

Reason (R): Class C amplifier is used at radio frequencies.

Both A and R are correct and R is correct explanation for A
Both A and R are correct but R is not correct explanation for A
A is correct R is wrong
A is wrong R is correct

⇒ The use of a capacitor filter in a rectifier circuit gives satisfactory performance only when the load
current is high
current is low
voltage is high
voltage is low

⇒ A dynamometer wattmeter can be used for
dc only
ac only
dc and 50 Hz ac
dc and high frequency ac

⇒ The characteristic equation of a control system is given as s⁴ + 8s³ + 24s² + 32s + K = 0. What is the range of values of K for this system to be stable?
0 ≤ K < 80
0 ≤ K < 100
0 ≤ K < 2300
0 ≤ K < 600