Question is ⇒ The ratio of specific weigh/h.p. of gas turbine and I.C engines may be typically of the order of, Options are ⇒ (A) 1 : 1, (B) 2 : 1, (C) 4 : 1, (D) 1:2, (E) 1 : 6., Leave your comments or Download question paper.

Question is ⇒ The ratio of specific weigh/h.p. of gas turbine and I.C engines may be typically of the order of, Options are ⇒ (A) 1 : 1, (B) 2 : 1, (C) 4 : 1, (D) 1:2, (E) 1 : 6., Leave your comments or Download question paper. Previous question Next question


Q1.	The ratio of specific weigh/h.p. of gas turbine and I.C engines may be typically of the order of
A.	1 : 1 [Wrong Answer]
B.	2 : 1 [Wrong Answer]
C.	4 : 1 [Wrong Answer]
D.	1:2 [Wrong Answer]
E.	1 : 6. [Correct Answer]
View Answer 3 -2 Explanation:- Answer : E Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Water is injected in gas turbine cycle to
control temperature
control output of turbine
control fire hazards
increase efficiency

⇒ During base load operation, the best method of controlling compressor is
start-stop motor
constant speed unloaded
relief valve
variable speed

⇒ Pick up the wrong statement about advantages of multistage compression
better lubrication is possible advantages of multistage
more loss of air due to leakage past the cylinder
mechanical balance is better
air can be cooled perfectly in between

⇒ The ideal efficiency of simple gas turbine cycle depends on
pressure ratio
maximum cycle temperature
minimum cycle temperature
all of the above

⇒ As the value of index '«' is decreased, the volumetric efficiency will
increase
decrease
remain unaffected
may increase/decrease depending on compressor clearance

⇒ Rotary compressors are suitable for
large discharge at high pressure
low discharge at high pressure
large discharge at low pressure
low discharge at low pressure

⇒ The hottest point in a gas turbine is
at the base
at the tip
in the center
between ~ to i of the blade height

⇒ Losses in a centrifugal compressor are due to
inlet losses
impeller channel losses
diffuser losses
all of the above

⇒ A centrifugal compressor works on the principle of
conversion of pressure energy into kinetic energy
conversion of kinetic energy into pres¬sure energy
centripetal action
generating pressure directly

⇒ The following is true for an open cycle gas turbine having exhaust heat exchanger. Atmospheric air before entering the compressor is
heated
compressed air before entering the combustion chamber is heated
bled gas from turbine is heated and readmitted for complete expansion
exhaust gases drive the compressor

⇒ Phenomenon of choking in compressor means
no flow of air
fixed mass flow rate regardless of pressure ratio
reducing mass flow rate with increase in pressure ratio
increased inclination of chord with air steam

⇒ Compression efficiency is compared against
ideal compression
adiabatic compression
botii isothermal and adiabatic compression
isentropic compression

⇒ Ratio of indicated h.p. to shaft h.p. in known as
compressor efficiency
isothermal efficiency
volumetric efficiency
mechanical efficiency

⇒ After-cooler is used to
cool the air
decrease the delivery temperature for ease in handling
cause moisture and oil vapour to drop out
reduce volume

⇒ Stalling of blades in axial flow compressor is the phenomenon of
air stream blocking the passage
motion of air at sonic velocity
unsteady periodic and reversed flow
air stream not able to follow the blade contour

⇒ Clearance volume in actual reciprocating compressors is essential
to accommodate Valves in the cylinder head
to provide cushioning effect
to attain high volumetric efficiency
to avoid mechanical bang of piston with cylinder head

⇒ In multistage compressor, the isothermal compression is achieved by
employing intercooler
by constantly cooling the cylinder
by running compressor at very slow speed
by insulating the cylinder

⇒ The work ratio of simple gas turbine cycle depends on
pressure ratio
maximum cycle temperature
minimum cycle temperature
all of the above

⇒ The compressor capacity with decrease in suction temperature
increases
decreases
remains unaffected
may increase or decrease depending on compressor capacity

⇒ Gas turbine works on
Brayton or Atkinson cycle
Carnot cycle
Rankine cycle
Erricsson cycle

⇒ Rotary compressor is best suited for
large quantity of air at high pressure
small quantity of air at high pressure
small quantity of air at low pressure
large quantity of air at low pressure

⇒ Out of the following, from where you will prefer to take intake for air compressor
from an air conditioned room maintained at 20°C
from outside atmosphere at 1°C
from coal yard side
from a side where cooling tower is located nearby

⇒ Maximum work is done in compressing air when the compression is
isothermal
adiabatic
polytropic
any one of the above

⇒ 1 m of air at atmospheric condition weighs approximately
0.5 kg
1.0 kg
1.3 kg
2.2 kg

⇒ Isothermal compression though most efficient, but is not -practicable because
it requires very big cylinder
it does not increase pressure much
it is impossible in practice
compressor has to run at very slow speed to achieve it

⇒ The overall isothermal eiffciency of compressor is defined as the ratio of
isothermal h.p. to the BHP of motor
isothermal h.p. to adiabatic h.p.
power to drive compressor to isothermal h.p.
work to compress air isothermally to work for actual compression

⇒ For supplying intermittent small quantity of air at high pressure, following compressor is best suited
centrifugal
reciprocating
axial
screw

⇒ The pressure ratio for an open cycle gas turbine compared to closed cycle gas turbine of same h.p. is
low
high
same
low/high depending on make and type

⇒ More than one stage will be preferred for reciprocating compressor if the delivery pressure is more than
2 kg/cm2
6 kg/cm2
10 kg/cm2
14.7 kg/cm2

⇒ Which is false statement about air receivers
These are used to dampen pulsations ,
These act as reservoir to- take care of sudden demands
These increase compressor efficiency
These knock out some oil and moisture