Question is ⇒ The purpose of series quadrature windings in amplidyne is to, Options are ⇒ (A) neutralize the effect of armature reaction, (B) reduce commutation difficulties, (C) increase the gain, (D) increase response time, (E) , Leave your comments or Download question paper.

Question is ⇒ The purpose of series quadrature windings in amplidyne is to, Options are ⇒ (A) neutralize the effect of armature reaction, (B) reduce commutation difficulties, (C) increase the gain, (D) increase response time, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The purpose of series quadrature windings in amplidyne is to
A.	neutralize the effect of armature reaction [Correct Answer]
B.	reduce commutation difficulties [Wrong Answer]
C.	increase the gain [Wrong Answer]
D.	increase response time [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The inverse Laplace transform of 1/(s - a)² is
e^at
t e^at
t² e^at
e^at/t

⇒ The maximum number of AM broadcast stations that can be accommodated in a 100 kHz bandwidth for the highest modulating frequency of 5 kHz will be
100
20
10
1

⇒ Which one is a linear system?
y[n] = x[n] x x[n - 1]
y[n] = x[n] + x[n - 10]
y[n] = x²[n]
(a) and (c)

⇒ In the words Kb or Mb used describing memory capacity, the letter b denotes
bits
bytes
bits or bytes depending on type of memory
bubbles

⇒ If the mantissa has a sign bit of 0 and the exponent is changed from a negative number to a more positive number the result is
a positive number and closer to zero
a positive number and away from zero
a negative number
a negative number and closer to zero

⇒

Assertion (A): When performance specifications are given in term of transient response characteristics, root locus method is a suitable method.

Reason (R): When performance specifications in terms of state variables are given, modern control methods can be used.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒ A system is said to be static system, when present output depend upon
present I/P
presrent and past
present and future
past and future

⇒ In a microwave resistor the wall thickness is made as small as possible to
have high value of R
have low value of R
minimize capacitive effect
reduce inductance

⇒ One of the major applications of JFET is in
switching
constant current-source
constant voltage-source
electron flow regulation

⇒ The factor n in the equation for calculating current for a silicon diode is
1
2
2.5
2 for low levels of current and 1 for high levels of current

⇒ Varactor diodes use
silicon
GaAs
either (a) or (b)
neither (a) nor (b)

⇒ As compared to an ordinary semiconductor diode, a Schottky diode
has higher reverse saturation current
has higher reverse saturation current and higher cut in voltage
has higher reverse saturation current and lower cut in voltage
has lower reverse saturation current and lower cut in voltage

⇒

Assertion (A): In a BJT, a_dc is about 0.98.

Reason (R): In a BJT, recombination in base region is high.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ The phenomenon known as "Early effect" in a BJT refers to a reduction of the effective base width caused by
electron-hole recombination at the base
reverse biasing of the base collector junction
forward biasing of emitter base junction
the early removal of stored base charge during saturation to cut off switching

⇒ Consider the following statements

Tellegen's theorem is applicable to any lumped network.
Reciprocity theorem is applicable to linear bilateral network.
Thevenin theorem is applicable to two terminal linear active network.
Norton's theorem is applicable to linear active network.

Which of the above statements are correct?
1, 2 and 3
1, 2, 3 and 4
1, 2 and 4
3 and 4

⇒ A sinusoidal signal with peak to peak amplitude of 1.536 volt is quantized into 128 levels using a mid-rise uniform quantizer. The quantization noise power is
0.768 V
48 x 10^-6 V
12 x 10^-6 V
3.072 Volt

⇒ A voltage of about 200 V dc can be measured
directly by dc potentiometer
by dc potentiometer in conjunction with a volt ratio box
a dc potentiometer in conjunction with a known resistance
both (b) and (c)

⇒ The bandwidth of FM for Commercial Purpose is
88 - 108 MHz
85 - 110 MHz
90 - 110 MHz
infinite Range

⇒ In sinusoidal PWM for inverters the width of different pulses are not the same.
TRUE
FALSE

⇒ Which of the following devices is used at the first stage of an electronic voltmeter?
BJT
SCR
MOSFET
UJT

⇒ The energy to cause thermionic emission is supplied by heating the cathode.
TRUE
FALSE

⇒ AB + AB =
B
A
1
0

⇒ Status register in the 8156 is read with
IN 20 H
OUT 20 H
either (a) or (b)
none of the above

⇒

Assertion (A): Electronic and Ionic polarization in a polyatomic gas are independent of temperature.

Reason (R): The orientation polarization is independent of temperature.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true

⇒ In a circular waveguide with radius r, the dominant mode is
TM₀₁
TE₀₁
TM₁₁
TE₁₁

⇒ Which one of the following is a passive device/Component?
Transformer
Oscillator
Generator
None

⇒ Satellites used for international communication are called
cossort
domsat
marisat
intelsat

⇒ In the full adder, denoting Sum by S and carry by C
S = 1 when two or more inputs are unity
C = 1 when two or more inputs are unity
C = 1 when all the inputs are unity
S = 1 when all the inputs are unity

⇒ A ramp input applied to a unity feedback system results in 5% steady state error. The type number and zero frequency gain of the system are respectively.
1 and 20
0 and 20
0 and 1/20
1 and 1/20

⇒ For the system of the given figure |G(jω)| = 0 dB at &omeg
0
1 rad/sec.
∞
2.38 rad/sec.