Question is ⇒ The purpose of connecting a coupling capacitor in the output circuit of an amplifier is, Options are ⇒ (A) to increase voltage gain, (B) to increase collector current, (C) to block dc collector voltage, (D) all of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ The purpose of connecting a coupling capacitor in the output circuit of an amplifier is, Options are ⇒ (A) to increase voltage gain, (B) to increase collector current, (C) to block dc collector voltage, (D) all of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The purpose of connecting a coupling capacitor in the output circuit of an amplifier is
A.	to increase voltage gain [Wrong Answer]
B.	to increase collector current [Wrong Answer]
C.	to block dc collector voltage [Correct Answer]
D.	all of the above [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ For measuring inductance with high Q, we should use
Maxwell's bridge
Maxwell Wien bridge
Hay's bridge
Either (a) or (b)

⇒ Satellites used for international communication are called
cossort
domsat
marisat
intelsat

⇒ What is the maximum output voltage from the 741 op-amp?
Zero
Approximately 1 V
Approximately 3 V
Approximately 5 V

⇒ Present day HVDC converters are all
3 pulse converters
6 pulse converters
12 pulse converters
either 6 pulse or 12 converters

⇒ Which converters uses integrating op-amp?
Parallel A/D converter
Single slope A/D converter
Dual slope A/D converter
Both (b) and (c)

⇒ In a CE amplifier circuit the ac voltage between emitter and ground
is very high
may be high or low
is zero
depends on circuit configuration

⇒ Two resistances of 2 Ω each are connected in series. A shunt having zero resistance is connected across the combination. The overall resistance will be
4 Ω
1 Ω
0.5 Ω
zero

⇒ As per time displacement theorem in Laplace transformation, displacement in the time domain by T becomes
division by s in the s domain
division by e^-sT in the s domain
multiplication by s in the s domain
multiplication by e^-sT in the s domain

⇒ For the collector-feedback amplifier shown below the voltage gain A_v will be _________
-113.07
-103.07
-107.07
-93

⇒ Surface integral of the electric field intensity is
differential of volume flux
electrical charge
net flux emanating from the surface
none of the above

⇒ When a bit is 0 is a DDR, it makes the corresponding port pin an __________ On the other hand, a 1 bit programs a __________ Pin.
output, input
output, output
input, input
input, output

⇒ Which of the following amplifiers has highest output impedance?
CE
CB
CC
Push pull

⇒ The conductivity of an intrinsic semiconductor is
generally less than that of a doped semiconductor
given by σ₁ = en_i (μ_n - μ_p)
given by σ₁ = en_i (μ_p + μ_n)
given by σ₁ = n_i (μ_n + μ_p)

⇒ In a ripple counter,
whenever a flip flop sets to 1, the next higher FF toggles
whenever a flip flop sets to 0, the next higher FF remains unchanged
whenever a flip flop sets to 1, the next higher FF faces race condition
whenever a flip flop sets to 0, the next higher FF faces race condition

⇒ The diagram to show distance time history of electrons in klystron amplifier is called
apple gate diagram
asynchronous diagram
bunching diagram
velocity modulation diagram

⇒ Which of the following statement is correct?
The input impedance of CE amplifier is usually around 10 Ω
The voltage gain of a transistor amplifier in CE mode is always less than unity
The output impedance of a transistor amplifier is independent of the transistor configuration
The voltage gain of a transistor amplifier is independent of the load resistance

⇒ The series element of a band stop filter is
capacitive
inductive
parallel combination of L and C
series combination of L and C

⇒ Which of the following pairs of octal and binary numbers are not equal?
111 11011₂ = 767₈
110110101₂ = 665₈
11010₂ = 3₈
10101.11₂ = 25.6₈

⇒ The system in the given figur
type 0 system
type 1 system
type 2 system
type 3 system

⇒ 24 telephone channels, each band limited to 3.4 kHz are to be time division multiplexed using PCM. If sampling frequency is 10 kHz and number of quantization levels is 128, the required bandwidth of PCM is
1.68 MHz
240 kHz
81.6 kHz
3.072 MHz

⇒ Consider the Schmitt trigger circuit shown below. A triangular wave which goes from - 12 V to 12 V is applied to the inverting input of the op-amp. Assume that the output of the op-amp moves from +15 V to -15 V. The voltage at the non-inverting switches bet
-12 V and +12 V
-7.5 V and +7.5 V
-5 V and +5 V
0 V and 5 V

⇒ The internal impedance of a source is 3 + j 7 Ω. For maximum power transfer, load impedance should be
3 + j 7 Ω
3 - j 7 Ω
7 + j 3 Ω
7 - j 3 Ω

⇒ Which of the following is used in temperature alarm circuits?
Thermistor
Photoconductor
Transistor
Varistor

⇒ To select one out of N equally probable events, the number of bits required is
log₂ N
log₁₀ N
log_e N
N

⇒ A clock signal coordinates the working of different flip flops.
TRUE
FALSE

⇒ In the given figure, the combinations of two non touching loop
1
2
3
4

⇒ The fact that domains exhibits spontaneous magnetisation is
first hypothesis is of Curie
second hypothesis is of Weiss
Curie-Weiss law
Boltzmann's statistics

⇒ The fluctuation in the received signal strength at the receiver of a random variation in the received signal is known as
fluctuation
fading
absorption
cycling

⇒ The resistance of the circuit shown is figur
5 Ω
More than 6 Ω
More than 4 Ω
Between 6 and 7 Ω

⇒ What is typical bandwidths of a 2-wire telephone line?
300 Hz to 3.4 kHz
20 Hz to 4 kHz
dc to 4 kHz
20 Hz to 20 kHz