Question is ⇒ The power taken by a 3-Φ load is given by the expression, Options are ⇒ (A) √3 VL IL sinΦ, (B) √3 VL IL cosΦ, (C) 3 VL IL sinΦ, (D) 3 VL IL cosΦ, (E) , Leave your comments or Download question paper.

Question is ⇒ The power taken by a 3-Φ load is given by the expression, Options are ⇒ (A) √3 VL IL sinΦ, (B) √3 VL IL cosΦ, (C) 3 VL IL sinΦ, (D) 3 VL IL cosΦ, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The power taken by a 3-Φ load is given by the expression
A.	√3 V_L I_L sinΦ [Wrong Answer]
B.	√3 V_L I_L cosΦ [Correct Answer]
C.	3 V_L I_L sinΦ [Wrong Answer]
D.	3 V_L I_L cosΦ [Wrong Answer]
View Answer 7 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The dual of a link is
Twig
Node
Loop
Tree branch

⇒ Power factor of the following circuit will be unity
Inductance
Capacitance
Resistance
Both (A) and (B)

⇒ The shunt element in a band pass filter is
Capacitive
Inductive
Parallel combination of L and C
Series combination of L and C

⇒ In a R-L-C series circuit if voltage V across the circuit is reduced to half the current I will change to
2 I
I/2
3/4 I
5/8 I

⇒ What inductance will give the same reactance as a capacitor of 2 µF when both are at 50 Hz?
5 H
10 H
15 H
20 H

⇒ Which of the following circuit component opposes the change in the circuit voltage
Inductance
Capacitance
Conductance
Resistance

⇒ At half power points of a resonance curve, the current is____ times the maximum current.
1/2
1/ √2
√2
2

⇒ In the R - L - C containing R = 4.5ω L = 0.06 H,C = 0.6 µF the power factor will be
Zero
Lagging
Leading
Unity

⇒ The product of apparent power and cosine of the phase angle between circuit voltage and current is
True power
Reactive power
Volt-amperes
Instantaneous power

⇒ For the same peak value, which of the following wave has the least mean value ?
Half wave rectified sine wave
Triangular wave
Sine wave
Square wave

⇒ The power factor of a D.C. circuit is always
Less than unity
Unity
Greater than Unity
Zero

⇒ Which of the following waves has the highest value of peak factor '?
Square wave
Sine wave
Half wave rectifier sine wave
Triangular wave

⇒ Selectivities of different resonance circuits are compared in terms of their
Impedances
Reactances
Frequencies
Band widths

⇒ The best place to install a capacitor is
Very near to inductive load
Across the terminals of the inductive load
Far away from the inductive load
Any where

⇒ For the full wave rectified sine wave the r.m.s. value is
0.707 I_max
0.636 I_max
0.318 I_max
Zero

⇒ Capacitive reactance is more when
Capacitances is less and frequency of supply is less
Capacitance is less and frequency of supply is more
Capacitance is more and frequency of supply is less
Capacitance is more and frequency of supply is more

⇒ Two waves of the same frequency have opposite phase when the phase angle between them is
360°
180°
90°
0°

⇒ For 200 V r.m.s. value triangular wave, the peak voltage will be
200 V
222 V
282 V
346 V

⇒ The dual of a loop is
Twig
Node pair
Mesh
Tree

⇒ The shunt element of prototype high pass filter is
Resistive
Inductive
Capacitive
Combination of L and C

⇒ The r.m.s. value of a sine wave is 100A. Its peak value is
70.7 A
141.4A
150A
282.8 A

⇒ In A.C. circuit laminated iron is invariably used in order to
Reduce eddy current loss
Increase heat radiation
Make assembly cheap and easier
Reduce circuit permeability

⇒ When an alternating current passes through an ohmic resistance the electrical power converted into heat is
Apparent power
True power
Reactive power
None of the above

⇒ The r.m.s. value of a sinusoidal A.C. current is equal to its value at an angle of____ degrees
90
60
45
30

⇒ For the same peak value which of the following wave will have the highest r.m.s. value ?
Square wave
Half wave rectified sine wave
Triangular wave
Sine wave

⇒ A network is said to be non-linear if it does not satisfy
Homogeneity condition
Superposition condition
Both (A) and (B)
Associative condition

⇒ In an A.C. circuit power is dissipated in
Resistance only
Inductance only
Capacitance only
None of the above

⇒ The power factor of a series R-L-C circuit at its half-power points is
Unity
Lagging
Leading
Lagging or leading

⇒ In a pure resistive circuit
Current lags behind the voltage by 90°
Current leads the voltage by 90°
Current can lead or lag the voltage by 90°
Current is in phase with the voltage

⇒ Poor power factor results in all of the following EXCEPT.
Overloading of transformers
Overloading of altemators
Reduction in power losses
Reduction in load handling capacity of electrical system